ETH Zurich 2014

Background information

We used an E. coli TOP10 strain transformed with two medium copy plasmids (about 15 to 20 copies per plasmid and cell). The first plasmid contained the commonly used p15A origin of replication, a kanamycin resistance gene, and one out of three cell-cell signaling promoters (pLux, pLas, or pRhl) followed by RBS (BBa_B0034) and superfolder green fluorescent protein (sfGFP). In general, for spacer and terminator sequences the parts BBa_B0040 and BBa_B0015 were used, respectively. The second plasmid contained the pBR322 origin (pMB1), which yields a stable two-plasmid system together with p15A, an ampicillin resistance gene, and a strong promoter (BBa_J23100) chosen from the Anderson promoter collection followed by LasR (BBa_C0179). The detailed construct designs and full sequences (piG0040, piG0058, piG0059,piG0059) are [http://2014.igem.org/Team:ETH_Zurich/lab/sequences available here].

Experimental Set-Up

The above described E. coli TOP10 strains were grown overnight in Lysogeny Broth (LB) containing kanamycin (50 μg/mL) and ampicillin (200 μg/mL) to an OD₆₀₀ of about 1.5 (37 °C, 220 rpm). As a reference, a preculture of the same strain lacking the sfGFP gene was included for each assay. The cultures were then diluted 1:40 in fresh LB containing the appropriate antibiotics and measured in triplicates in microtiter plate format on 96-well plates (200 μL culture volume) for 10 h at 37 °C with a Tecan infinite M200 PRO plate reader (optical density measured at 600 nm; fluorescence with an excitation wavelength of 488 nm and an emission wavelength of 530 nm). After 200 min we added the following concentrations of inducers (3OC6-HSL, 3OC12-HSL, and C4-HSL): 10^-4 nM and 10⁴ nM (from 100 mM stocks in DMSO). Attention: All the dilutions of 3OC12-HSL should be made in DMSO in order to avoid precipitation. In addition, in one triplicate only H₂O was added as a control. From the the obtained kinetic data, we calculated mean values and plotted the dose-response-curves for 200 min past induction.

Characterization of crosstalk

Background information

Here, we focus on the characterization of crosstalk of regulator LasR and promoter pLas in combination with different AHLs and further crosstalk of LasR and inducer C4-HSL with the three promoters - pLux, pLas, and pRhl.

First-order crosstalk

In the first order crosstalk section we describe crosstalk of pLas due to LasR binding to inducers different from 3OC12-HSL or pLas itself binding to a regulator-inducer pair different from LasR-3OC12-HSL.

First Level crosstalk: LasR binds to different HSL and activates the promoter Plas

In the conventional system 3OC12-HSL binds to its corresponding regulator, LasR, and activates the pLas promoter (figure 2, red). However, LasR can potentially also bind other AHLs and then activate pLas (figure 2, 3OC6-HSL in light blue and C4-HSL in green).

Second Level crosstalk: LasR binds to 3OC12-HSL, its natural HSL, and activates different promoter

Second order crosstalk: Combination of both cross-talk levels

Results

Table 1 Crosstalk matrix for the regulator LasR (BBa_C0179)

In all the measurements conducted to create this matrix the regulator LasR was the basis and was induced in six different variations shown.

Modeling crosstalk

Each experimental data set was fitted to an Hill function using the Least Absolute Residual method.

The fitting of the graphs was performed using the following equation :

rFluo = the relative fluorescence (absolute measured fluorescence value over OD)[a.u.]
a = basal expression rate [a.u.](“leakiness”)
b = maximum expression rate [a.u.]("full induction")
n = Hill coefficient (“cooperativity”)
K_m = Half-maximal effective concentration (“sensitivity”)
[AHL] = AHL concentration [nM]

Antiquity

This review comes from the old result system and indicates that this part did not work in some test.

No review score entered. Northwestern 2011

The 2011 Northwestern iGEM team used this part as a part of our Pseudomonas Aeruginosa biosensor. We were able to successfully express RhlR (C0171) continuously in our system. BBa K575032

iGEM Dundee 2014

Dundee iGEM 2014 used this lasR coding sequence to build two composite parts termed BBa_K1315009 and BBa_K1315010. These were designed as biosensors for Pseudomonas aeruginosa AutoInducer-1 (PAI-1), and were to be used in a bio-electronic device to improve diagnostics for Cystic Fibrosis patients. Details of experimental work are logged on the experience pages of BBa_K1315009 and BBa_K1315010.