Difference between revisions of "Part:BBa K325909:ArabinosetoLight"

Description
This page describes the light output of BBa K325909 as a fucntion of Arabinose concentration in the media. The characterisation has been made in different chassis. TOP 10 cells as well as 2 mutants in which expression of H-NS was repressed.

THIS PAGE IS CURRENTLY BEING UPDATED.

Data

Figure 1 - Light output of BBa_K325219 as a function of Arabinose concentration in the media. The values correspond to the peak intensity within 5 hours of adding Arabinose to the media. Data points and error bars correspond to the mean and the standard deviation of 3 time repeats.

Figure 2 - Evolution of luminescence with time at different Arabinose concentrations for BBa_K325219. Measurements were taken every 30 minutes. Data points and error bars correspond to the mean and standard deviation of 3 time repeats.

Protocol

1. Three 5 ml cultures of [http://openwetware.org/wiki/Endy:M9_media/supplemented supplemented M9 medium] and antibiotic (kanamycin, 20 µg/ml) were inoculated with single colonies (~2mm ø) from a freshly streaked plate of MG1655 containing BBa_T9002. One 5 ml culture was inoculated with a single colony from a freshly streaked plate of MG1655 containing a BBa_T9002 mutant (T9002m) lacking a GFP expression device described in the stability section.
2. Cultures were grown in 17 mm test tubes for 15 hrs at 37°C with shaking at 70 rpm.
3. Cultures were diluted 1:1000 into 5.5 ml of fresh medium and grown to an OD600 of 0.15 under the same conditions as before. This growth took on average 4.5 hrs.
4. Twenty-four 200 µl aliquots of each of the cultures were transferred into a flat-bottomed 96 well plate (Cellstar Uclear bottom, cat. # T-3026-16, Greiner).
5. 2 µl of the stock concentrations of the cognate AHL, 3-oxohexanoyl-homoserine lactone (3OC₆HSL), was added to each well to yield 8 different final concentrations (0, 1E-10, 1E-9, 1E-8, 1E-7, 1E-6, 1E-5 and 1E-4 M). Three replicate wells were measured for each concentration of 3OC₆HSL. Three wells were each filled with 200 µl of medium to measure the absorbance background. Three further wells were each filled with 200 µl of the BBa_T9002 mutant culture to measure fluorescent background.
6. The plate was incubated in a [http://openwetware.org/wiki/Endy:Victor3_plate_reader Wallac Victor3 multi-well fluorimeter] (Perkin Elmer) at 37°C and assayed with an automatically repeating protocol of absorbance measurements (600 nm absorbance filter, 0.1 second counting time through 5 mm of fluid), fluorescence measurements (488 nm excitation filter, 525 nm emission filter, 0.5 seconds, CW lamp energy 12901 units), and shaking (1 mm, linear, normal speed, 5 seconds). Time between repeated measurements was 2 min and 21 s. Approximately 6 min elapsed between beginning addition of 3OC₆HSL to the wells and the first plate reader measurement. 3OC₆HSL was added in order of increasing concentration to minimize GFP synthesis during plate loading. Cells appear to grow exponentially for the duration of the plate reader measurement protocol (see Figure 2 for representative growth curves).
7. We repeated steps 1 through 6 on three separate days to obtain data for nine colonies from a single plate.
8. We processed the data to compute the PoPS output from BBa_F2620 as described on the Data analysis page. The data for each colony tested was averaged across the three replicate wells. The mean for each colony was then averaged to obtain a population mean. The time and dose dependent input-output surface is shown above in Figure 3. Following an initial transient response, device output reached an approximate steady state.
9. The snapshot transfer function in Figure 1 is the 60 min time-slice from the surface shown in Figure 3 (highlighted as a heavy black line). Error bars in Figure 1 representing the 95% confidence interval in the population for the nine independent samples. The cyan shaded region represents the range of the nine independent samples.
10. To estimate parameters that characterize the measured transfer function, we used least squares estimation to fit a simple model to the data. A Hill equation derived from simple biochemical equations describes the data well (R²=0.99). In the equation (shown below), P_out is the PoPS per cell output of BBa_F2620, P_max is the maximum output level, K is the switch point, and n is the hill coefficient describing the steepness of the transition from low output to high output.
11. To gain further information about the transition region of the transfer function, measurements were subsequently taken at two intermediate 3OC₆HSL concentrations (3.3E-09 M and 3.3E-08 M) using the same protocol defined above. Measurements were simultaneously taken at a subset of the original concentrations to ensure the new data was consistent with the earlier data. The new data was processed simultaneously with the original data, with the exception that only six independent colonies were measured for the intermediate 3OC₆HSL concentrations.

<math> P_{out} = \frac{P_{max}[3OC_6HSL]^n}{K^n+[3OC_6HSL]^n} </math>