Terminator

Part:BBa_B0012

Designed by: Reshma Shetty   Group: Antiquity   (2003-01-31)
Revision as of 02:46, 25 August 2020 by Nradde (Talk | contribs)

Terminator.png

biologyT7TE
directionForward
forward_efficiency0.309[CC]
reversed_version590
reverse_efficiency-0.368[CC]

TE from coliphageT7

  • Transcription terminator for the E.coli RNA polymerase.
  • (This is a bad terminator,)
  • (It is a promoter in the reverse direction.)

Secondary Structure

Mfold-B0012-1.png




Assembly Compatibility:
  • 10
    COMPATIBLE WITH RFC[10]
  • 12
    COMPATIBLE WITH RFC[12]
  • 21
    COMPATIBLE WITH RFC[21]
  • 23
    COMPATIBLE WITH RFC[23]
  • 25
    COMPATIBLE WITH RFC[25]
  • 1000
    COMPATIBLE WITH RFC[1000]

Measurement

  • [http://openwetware.org/wiki/Cconboy:Terminator_Characterization/Results How these parts were measured]


>Internal Priming Screening Characterization of BBa_B0012: Has no possible internal priming sites between this BioBrick part and the VF2 or the VR primer.

The 2018 Hawaii iGEM team evaluated the 40 most frequently used BioBricks and ran them through an internal priming screening process that we developed using the BLAST program tool. Out of the 40 BioBricks we evaluated, 10 of them showed possible internal priming of either the VF2 or VR primers and sometime even both. The data set has a range of sequence lengths from as small as 12 bases to as large as 1,210 bases. We experienced the issue of possible internal priming during the sequence verification process of our own BBa_K2574001 BioBrick and in the cloning process to express the part as a fusion protein. BBa_K2574001 is a composite part containing a VLP forming Gag protein sequence attached to a frequently used RFP part (BBa_E1010). We conducted a PCR amplification of the Gag-RFP insert using the VF2 and VR primers on the ligation product (pSB1C3 ligated to the Gag + RFP). This amplicon would serve as template for another PCR where we would add the NcoI and BamHI restriction enzyme sites through new primers for ligation into pET14b and subsequent induced expression. Despite gel confirming a rather large, approximately 2.1 kb insert band, our sequencing results with the VR primer and BamHI RFP reverse primer gave mixed results. Both should have displayed the end of the RFP, but the VR primer revealed the end of the Gag. Analysis of the VR primer on the Gag-RFP sequence revealed several sites where the VR primer could have annealed with ~9 - 12 bp of complementarity. Internal priming of forward and reverse primers can be detrimental to an iGEM project because you can never be sure if the desired construct was correctly inserted into the BioBrick plasmid without a successful sequence verification.

Functional Parameters: Austin_UTexas

BBa_B0012 parameters

Burden Imposed by this Part:

Burden Value: -0.5 ± 2.4%

Burden is the percent reduction in the growth rate of E. coli cells transformed with a plasmid containing this BioBrick (± values are 95% confidence limits). This BioBrick did not exhibit a burden that was significantly greater than zero (i.e., it appears to have little to no impact on growth). Therefore, users can depend on this part to remain stable for many bacterial cell divisions and in large culture volumes. Refer to any one of the BBa_K3174002 - BBa_K3174007 pages for more information on the methods, an explanation of the sources of burden, and other conclusions from a large-scale measurement project conducted by the 2019 Austin_UTexas team.

This functional parameter was added by the 2020 Austin_UTexas team.

[edit]
Categories
//direction/forward
//terminator/single
Parameters
biologyT7TE
directionForward
forward_efficiency0.309[CC]
reversed_version590
reverse_efficiency-0.368[CC]