Part:BBa_K2003011:Experience

This experience page is provided so that any user may enter their experience using this part.
Please enter how you used this part and how it worked out.

Results

Designing the UnaG BioBricks

The IDT plasmid contains the lac-promoter so it is possible to do test expression directly with IPTG. However due to the way the final product is created, the UnaG sequence had a 50% chance to be incorporated in reverse, which was the case. Therefore different BioBrick promoters were extracted from the 2016 distribution to test for expression. Those include a medium constitutive promoter (BBa_K608006), a strong constitutive promoter (BBa_K880005), IPTG inducible promoter (BBa_J04500), and a T7 promoter (BBa_K525998). All of those contain an RBS already assembled in order to speed up work. The UnaG sequence itself was excised from the IDT plasmid using EcoRI and PstI and ligated into pSB1C3 backbone cut with the same set of enzymes.

After successfully obtaining UnaG assembled with a variety of promoters, mutagenesis was performed in order to create several variants of the BioBrick for future use. The “stock” option contains the UnaG coding sequence. Upstream of it lies a 6xHis affinity tag, separated by an additional Serine amino acid to increase flexibility between the tag and the protein. In the registry it is annotated as BBa_K2003010. Note that this part is designed with RFC25 (Freiburg Standard) prefix and suffix in mind, hence it contains additional restriction sites, that do not affect normal 3A assembly but enable in-frame protein fusion without creating stop codons. Downstream of the part lies a short Glycine-rich flexible linker to minimize the effects of possible protein fusion. However the base part still contains the double TAA codons before this flexible linker.

The stop signal has been removed with PCR in BBa_K2003011. This is part retains all the features, including the RFC25 prefix and suffix, but now the flexible linker is properly expressed and in case of fusing to another CDS would not cause premature termination.

Finally, to avoid potential interference from the 6xHistidine affinity tag, BBa_K2003012 was created based on BBa_K2003011. In this part, the six amino acids were removed (again through PCR), as well as the Serine linker in between. This part has been designed for studying the properties of the protein in vivo, since the high positive charge of the affinity tag could interfere with its function or localization. At each step of the experiments, sequencing was performed using the iGEM standard VF2 and VR verification primers to ensure CDS integrity and especially to avoid introduced frameshift mutations.

Small-scale Expression of UnaG

In addition to mutagenesis experiments, small-scale expression tests were performed to verify that UnaG expresses under our laboratory conditions (originally the protein was purified and crystalized using Escherichia coli, so it should be producible in prokaryotes). BioBricks BBa_K880005 and BBa_K2003010 were 3A assembled and grown overnight in LB. Bilirubin is not very soluble in water, so the stock 1mM solution was prepared in DMSO instead. It seems the molecule does not permeate the cell easily, so appropriate amounts were added to crude cell extracts instead, to a final concentration of 100 µM. Those were obtained by replacing the growth medium with room temperature PBS pH 7.4 containing 1mg/ml lysozyme and breaking open the cells through incubation for 30 minutes and occasional mixing. To avoid unspecific fluorescence, cell debris were pelleted before the experiment and small aliquots of the supernatant were added to 200 µL thin-walled PCR tubes. Results are displayed in the Figures 1 and 2:

Figure 1. Preliminary test of UnaG.

Figure 2. Comparative fluorescence of crude cell extracts of DH5a cells expressing UnaG or RFP.

Large-scale expression of UnaG

IMAC Chromatography Setup

After observing the small-scale expression results, plans for large-scale purification were designed. E.coli BL21DE3 cells were used in conjunction with T7 promoter-driven UnaG in TB medium to achieve peak levels of expression. T7 expression is induced using IPTG at 18° for 16 hours. Breaking open the cells was performed using Qsonica Q700 titanium-tip sonicator since lysozyme has nearly the same size as UnaG and would make purification more difficult, as well as just slower and less efficient compared to sonication. It also breaks DNA, reducing overall lysate viscosity. After centrifugation at 4°C and 10 000 g for 1 hour, the supernatant was filtered through 0.2 µM pore filter and loaded to a Ni²⁺ affinity column.

Figure 3. SDS Page Results Coomasie stained gel representing the eluted fractions of protein; L - PageRuler™ Prestained Protein Ladder, 10 to 180 kDa; 1 to 7 = incteasing concentrations of imidazole: from 50 to 350 mM in 50 mM steps respectively;

First the column had to be packed using Nickel Sepharose Fast Flow resin (GE Healthcare). The calculated column volume for this setup was 5 ml. Afterwards the column had to be charged with Ni²⁺ this is done with a ion binding buffer (50 mM Na⁺CH₃COO^-, 300 mM NaCl, pH4). The column was equilibrated by pumping through 5 column volumes (CV) with a flowrate of 0.7ml/min. After the column is equilibrated with ion binding buffer, the buffer it switched out with 0.3 M NiSO₄ and a new equilibration step is made with 5CV’s of ion solution. The final equilibration is done with 5CV ion binding buffer to wash away all of the excess Ni⁺² ions.

Three others buffers were prepared, having a base composition of 50 mM Na⁺CH₃COO^- and 300 mM NaCl. The binding buffer for UnaG contains 10 mM imidazole, the washing buffer (to remove the excess protein from the column) contains 20 mM imidazole and the elution buffer contains 350 mM imidazole. The column is equilibrated with 5 CV of binding buffer, afterward 25 ml of the binding buffer is mixed with the UnaG lysate and loaded onto the column. Afterwards 5 CV of wash buffer is pumped through to remove of all the excess protein still in the column. Finally the elution buffer is used and fractions are collected. All of the fractions were then tested for the target protein using SDS-PAGE (Figure 3).

Samples were boiled with 2x Laemmli Sample Buffer with DTT and 10 µL loaded on each start. The protein ladder was 5 µL, not boiled. After staining the gel with Coomassie Brilliant Blue and destaining, the band corresponding to UnaG’s expected size (15.6 kDa) was not observed anywhere. In addition, none of the fractions fluoresced when bilirubin was added.

Since sequencing confirmed that there are no mutations, and we previously managed to obtain impure functioning UnaG during the small-scale experiments of UnaG, the conclusion was that the IPTG solution was faulty and did not manage to induce the T7 promoter driven UnaG expression.

User Reviews

UNIQ387f583f9ac6745c-partinfo-00000005-QINU UNIQ387f583f9ac6745c-partinfo-00000006-QINU