DNA

Part:BBa_K4765109

Designed by: Siliang Zhan   Group: iGEM23_Fudan   (2023-09-30)
Revision as of 06:00, 11 October 2023 by Siliang Zhan (Talk | contribs)

Twister P1 + T7_RBS + intimin-MVN fusion + stem-loop

contributed by Fudan iGEM 2023

Introduction

We’ve developed an E. coli-cyanobacteria adhesion module by transfecting intimin-MVN fusion. Intimin-MVN fusion is composed of intimin and MVN. MVN is a lectin isolated from the cyanobacteria Microcystis aeruginosa PCC7806 and it was tested by iGEM14_Peking. Intimin which includes a short N-terminal signal peptide to direct its trafficking to the periplasm, a LysM domain for peptidoglycan binding, and a beta-barrel for transmembrane insertion[1] , possesses the outer membrane anchoring of MVN. We’ve constructed this fusion protein into our ribozyme-assisted polycistronic co-expression system:pRAP.

Usage and Biology

This biological component delivers MVN to the surface of E. coli, facilitating adhesion between E. coli and Microcystis aeruginosa PCC7806. We envision that the adhesion between cyanobacteria and E. coli can promote the exchange of substances within the biofilm, enhancing the biofilm's survivability.

Characterization

Sequencing map

contributed by Fudan iGEM 2023
Figure1 Sequencing map of MVN

Sequencing starts from the T7 terminator, with the primer 5-GCTAGTTATTGCTCAGCGG-3.


Aggregation Assay

To validate the role of intimin-MVN in mediating the binding of E.coli and Microcystis aeruginosa, we conducted sedimentation experiments. Specifically,bacterial solutions of aTc-induced/not-induced intimin-MVN E.coli + Microcystis aeruginosa, were mixed in a 1:1 ratio (600μL per strain per tube, independent experiment repeat 3 times) and allowed to settle. Sampling was performed at 0, 2, 6,and 24 hours by collecting 100μL aliquots from the upper 25% of each mixture (supernatant) in each tube at each time point. These samples were subsequently transferred to EP tubes and stored at 4℃ until the final sampling. Afterward, they were resuspended and transferred to a 96-well assay plate for OD~600~ and OD~685~ measurement. The percentage of bacteria remaining in the supernatant at 6 hours was determined by dividing the bacterial count at 6 hours (as determined by the OD~600~ and OD~685~ measurement) by the bacterial count at 0 hours.

As shown in Figure 2, at 6 hours, in the aTc-induced E. coli / Microcystis aeruginosa samples, bacteria percentage remaining in the supernatant was significantly lower compared to the uninduced samples. As shown in Figure 3, For aTc-induced intimin-MVN E.coli / Microcystis aeruginosa mixed samples, the bacterial count at 2 hours and 6 hours was significantly lower than the uninduced type. These results suggests that intimin-MVN can facilitate the connection between the two entities and promote biofilm formation within a relatively short time.

contributed by Fudan iGEM 2023
Figure 2: Bacteria Percentage Remaining in the Supernatant at 6 Hours

The bacterial quantity in the supernatant is reflected by measuring the OD~600~ (1 OD~600~ corresponds to 10^8 bacterial particles).

contributed by Fudan iGEM 2023
Figure 3: Bacteria Remaining in the Supernatant at 0,2,6,24 Hours

The bacterial quantity in the supernatant is reflected by measuring the OD~600~ (1 OD~600~ corresponds to 10^8 bacterial particles).

Sequence and Features


Assembly Compatibility:
  • 10
    COMPATIBLE WITH RFC[10]
  • 12
    COMPATIBLE WITH RFC[12]
  • 21
    COMPATIBLE WITH RFC[21]
  • 23
    COMPATIBLE WITH RFC[23]
  • 25
    COMPATIBLE WITH RFC[25]
  • 1000
    INCOMPATIBLE WITH RFC[1000]
    Illegal BsaI site found at 1305
    Illegal SapI site found at 2058

Reference

  1. Piñero-Lambea, C., Bodelón, G., Fernández-Periáñez, R., Cuesta, A. M., Álvarez-Vallina, L., & Fernández, L. Á. (2015). Programming controlled adhesion of E. coli to target surfaces, cells, and tumors with synthetic adhesins. ACS Synthetic Biology, 4(4), 463–473. https://doi.org/10.1021/sb500252a
[edit]
Categories
//collections/biofilm
Parameters
protein