Part:BBa_K3331012
E.coli galU+E.coli pgmA
This part can increase the yield of EPS. The yield of EPS can be significantly increased by overexpressing two key enzymes galU and pgmA at the same time. The part galU is from Escherichia coli YJ4. The part pgmA is from Escherichia coli str. K-12 substr. MG1655 Reference: Levander Fredrik et al. Applied and environmental microbiology,2002,68(2).
Sequence and Features
- 10COMPATIBLE WITH RFC[10]
- 12COMPATIBLE WITH RFC[12]
- 21COMPATIBLE WITH RFC[21]
- 23COMPATIBLE WITH RFC[23]
- 25COMPATIBLE WITH RFC[25]
- 1000COMPATIBLE WITH RFC[1000]
Overview
In order to increase the production of exopolysaccharides (EPSs), we altered the levels of enzymes in the central metabolism. We selected and overexpressed two key enzymes, galU and pgmA at the same time. And we found we successfully enhance the production of EPSs in E.coli.DH5α
Characterization
The test plasmid was constructed by Golden Gate Assembly and was confirmed by colony PCR. The length of E.coli galU fragment is 981bp, and the length of E.coli pgmA is 1770bp. The following results showed successful constructions.
Our strain was cultured in ampicillin-resistant LB medium with strictly control variables. We stop the culture after 24 hours of culture. We measure the expression of EPS and the level of gene transcription during this period. RT-qPCR was conducted to test their expressions. And we can see these two genes were transcribed successfully.
Anthrone sulfuric acid method was used to detect EPS yields. Compared with the blank strain, the EPS yield of the engineering strain increased by 106.4%. The results of this study clearly show that it is possible to enhance the production of EPSs in DH5α by altering the expression of this part.
We also measured the growth of DH5α transferred into the plasmid by enzyme labeling instrument. We measure the OD value of bacteria every hour under the wavelength of 600nm and fit the results. It was compared with the blankDH5α and the growth curve was drawn.
Improvement from XJTU-China-2022 iGEM
Profile
Base Pairs
6356
Design Notes
we found that using the pSEVA341 plasmid Replacing the medium-high copy pSB1K3 plasmid as a vector resulted in a higher degree of expression as well as a more significant stability of gene expression The pSEVA plasmid allows direct binding to express heterologous genes and retains polyclonal sites after binding to any gene. This modularity and compatibility with various replicons allows the assembly of complex circuits in the same host, and the ease of monitoring and modular control of each subcircuit helps ease the transition from trial-and-error genetic engineering to systematic synthetic biology. It is more beneficial for the characterization and practical application of modular research in synthetic biology. [2]We also designed the introduction of LacI regulatory protein to obtain the target gene expression product more accurately and efficiently, and to achieve better ability to regulate the product to achieve water fixation and moisture retention.
Usage&Biology
The original components are replaced with carriers to achieve more efficient expression
To facilitate the modularized design of plasmids, we named the EPS synthesis verification plasmid 4, which will be referred to as plasmid 4 in the following paragraphs. Plasmid 4 is a gene vector for the synthesis of EPS extracellular polysaccharides. The main gene progenitor contains the EPS synthesis gene, LacI regulatory protein synthesis gene + Ptrc promoter, as shown in Figure 1.
Figure 1
1. Introduction to extracellular polysaccharide synthesis
We hope to produce extracellular polysaccharide EPS in engineered bacteria by plasmid IV to achieve soil fixation and moisture retention, and the principle of EPS synthesis by plasmid IV in bacteria is that: glucose enters the hexose diphosphate pathway (EMP) or synthesizes glucose-1-phosphate catalyzed by PGM, and then UDP is synthesized by UDP glucose pyrophosphorylase (galU). UDP glucose can be used as a raw material for synthesizing EPS. Also after reviewing the literature, we found that Fredrik Levander and his team overexpressed pgmA and galU genes in Streptococcus thermophilus[1]. They found that EPS production in Streptococcus thermophilus increased from 0.17 g/mol to 0.31 g/mol when galU and pgmA (encoding phosphoglucose mutase (PGM)) were overexpressed, and we hypothesized that overexpression of pgmA and galU genes in bacteria would also increase extracellular polysaccharide production. Therefore, we wanted to overexpress pgmA gene and galU gene in engineered bacteria to achieve high extracellular polysaccharide production[1], the principle of which is shown in Figure 2.[1] https://2020.igem.org/Team:XJTU-China/Engineering
Figure 2
2. Construction and validation of extracellular polysaccharide synthesis plasmid 4
Based on the work of the XJTU-2020 team, we selected the E.coli-pgmA+E.coli-Galu gene (later referred to as EE gene) with the best EPS expression (as shown in Figure IV ) with the LacI manipulator (GenBank: NC_000913.3 ) to form plasmid IV (Figure III ) where the GalU gene (sequence GenBank: CP104721.1) and the pgmA（GenBank: CP041425.1） gene set from E. coli were synthesized into the EE gene, In specific experiments, we obtained the EE gene, LacI gene in separate isolation and extraction (Figure In our specific experiments, we isolated and extracted EE gene, LacI gene (Figure 6 and 7) pSB1K3 plasmid vector and recovered them, and then performed GoldenGate ligation by using Bsa I enzyme cleavage site. Because the plasmid copy number was not high, we were unable to obtain the linker. So we changed to a high copy pSEVA341 plasmid and re-linked it to obtain new plasmid IV and successfully constructed it (Figure iii). pSEVA plasmid allows direct binding to express heterologous genes and retains polyclonal sites after binding to any gene. This modularity and compatibility with various replicons allow the assembly of complex circuits in the same host, and the ease of monitoring and modular control of each subcircuit helps ease the transition from trial-and-error genetic engineering to systematic synthetic biology. It is more beneficial for the characterization and practical application of modular research in synthetic biology.[2]
Figure 3: 2022 experimental group plasmids
Figure 4: 2020 EPS expression molar concentration comparison
Figure 5 (colony PCR) modified plasmid IV was successfully gelled
Figure 6: pgmA and GalU gene extraction gum map
Figure 7: Lac gene gum map
Figure 8: Design of plasmid 4
3.Improvements to the 2020 iGEM team
As shown in the FIG6, compared to the EE plasmid constructed by team 2020-XJTU-China, our EPS synthesis plasmid showed increased transcriptional levels for both galU and pgmA gene. After IPTG induction, the expression levels of galU and pgmA gene were 3.4 and 2.8 fold compared to that of EE, demonstrating the improvement after promoter and replicon optimization.PSEVA plasmid allow direct expression of heterologous genes, still more after combined with any genetic cloning sites, this modular and various replicon compatibility allows assembly in the same host complex circuit, and each child circuit are easy to monitor and modular control help from trial-and-error type of genetic engineering to the system of synthetic biology. It is beneficial to the characteristic display and practical application of synthetic biology modular research. Comparison of RT-qPCR was shown below：
IPTG was induced at a concentration of 1mM for 6h at 37℃.
4.Determination of EPS content
Anthraxone colorimetry is a fast and convenient sugar fixation method, under strong acidic conditions, anthraconone can be associated with free or polysaccharides present in hexose, pentose and hexoclonic acid to generate blue-green glycal derivatives, the depth of its color and the sugar content in a certain range is proportional, the maximum absorption peak at 620nm. In this experiment we can semi-quantitatively compare the synthetic amount of EPS of engineered bacteria by this method. First, we used glucose at concentrations of 0, 0.2, 0.4, 0.6, and 0.8 (units of mg/ml) as standard solutions to determine the standard curve at 620 nm. (FIG 7)
FIG 9-10: Shows the color change of the standard curve data using glucose as a standard solution versus the different concentrations of the standard solution. In order to exclude the influence of the sugars contained in LB medium on the experimental results during the experiment, we isolated the relatively pure bacteria by alcoholic deposition and detected the relative expression of the sugar content, and we showed the experimental results in FIG8.
FIG 11: Shows the relative absorbance of three different bacterial purification solutions at 620 nm (calculated as the ratio of absorbance to liquid concentration), *indicating that there are significant differences in this sample compared to EE bacteria (based on T-TEST).
Compared with the engineering bacteria introduced into the EE plasmid, the expression of polysaccharides introduced into the engineering bacteria of plasmid 4 has been significantly improved (P<0.05) We can consider that the part of the increase is due to the introduction of plasmid 4, the synthesis of additional EPS. From this we preliminarily prove that the construction of plasmid 4 is successful and effective.
References
[1]Rafael Silva-Rocha, Esteban Martínez-García, Belén Calles, Max Chavarría, Alejandro Arce-Rodríguez, Aitor de las Heras, A. David Páez-Espino, Gonzalo Durante-Rodríguez, Juhyun Kim, Pablo I. Nikel, Raúl Platero, Víctor de Lorenzo, The Standard European Vector Architecture (SEVA): a coherent platform for the analysis and deployment of complex prokaryotic phenotypes, Nucleic Acids Research, Volume 41, Issue D1, 1 January 2013, Pages D666–D675, https://doi.org/10.1093/nar/gks1119
[2]Jorge Alonso-Gutierrez, Rossana Chan, Tanveer S. Batth, Paul D. Adams, Jay D. Keasling, Christopher J. Petzold, Taek Soon Lee, Metabolic engineering of Escherichia coli for limonene and perillyl alcohol production, Metabolic Engineering, Volume 19,2013, Pages 33-41, ISSN 1096-7176,https://doi.org/10.1016/j.ymben.2013.05.004.
[3]Figurski, D.H. and Helinski, D.R. (1979) Replication of an origin-containing derivative of plasmid RK2 dependent on a plasmid function provided in trans. Proc. Natl Acad. Sci. USA, 76, 1648–1652.
[4]Santos,P.M., Di Bartolo,I., Blatny,J.M., Zennaro,E. and Valla,S.(2001) New broad-host -range promoter probe vectors based on the plasmid RK2 replicon. FEMS Microbiol. Lett., 195, 91–96.
[5]LEVANDER F, SVENSSON M, RåDSTRöM P. Enhanced Exopolysaccharide Production by Metabolic Engineering of Streptococcus thermophilus [J]. Applied and Environmental Microbiology, 2002, 68(2): 784-90.
| None |