Part:BBa_K3570006

DPP1 upstream homologous sequence

Usage

DPP1 upstream homology arm part shall be used together with DPP1 downstream homology arm part (BBa_K3570007) to target a functional yeast integration locus. When DPP1 up put to 5' of the biobrick together with DPP1 downstream to the 3', the biobrick can be integrated into the S. cerevisiae's genome. It will do homologous recombination within the Diacylglycerol pyrophosphate phosphatase 1 (DPP1) gene.

This sequence was identified from a personal communication with Dr. Gilles Truan.

Experiments

We used this part in the insertion of the tHMG1 and CrtE genes (part BBa_K3570000) in the yeast genome. Below is our cloning strategy and our experiments which show that we have successfully integrated this part and that the BBa_K3570006 and BBa_K3570007 parts work.

A. Protocols
1. Preparation of yeast competent cells
- Materials
75 mL of YPD medium.
50mL falcon-tube.
Centrifuge
26mL of LiAc/TE.
- Methods

Overnight preculture from a fresh colony of yeast in 25mL of YPD.

Dilute overnight precultures to low OD600 (e.g. 0.05) in 50 ml fresh YPD medium.

Mesure concentration every 2h to 3h until it reaches an OD of around 0.8.

Transfer 50mL to a 50mL falcon-tube and centrifuge 5min at 3000rpm (room-temperature).

Remove flow-thru and add 25mL of LiAc/TE, mix thoroughly by inverting the tube 10 times.

Centrifuge 5min at 3000rpm (at room-temperature).

Remove flow-thru.

Add 400uL of LiAc/TE, mix thoroughly by inverting the tube 10 times.
Yeast competent cells should be used on the same day that they have been prepared.

<p>2. Yeast transformation

Materials

Transforming DNA

Competent yeast cells

10mg/ml carrier DNA (SS-DNA)

50% PEG in 100mM LiAc/TE

NaCl

YNB plates (with all the amino acids except for the ….)

30ºC warm bath

42ºC warm bath

30ºC incubator

table-top microcentrifuge

1.5mL microcentrifuge tube

Method

1. Prepare mix in 1.5mL microcentrifuge tube:

</p>

B. Results and discussion:

2. Yeast transformation:

Since the construction of the part BBa_K3570000 was successful, we proceeded to the next step: integration in the yeast genome. The plasmid was digested with enzymes SbfI and EcoRI and purified to transform the yeast Saccharomyces cerevisiae. The yeast was then grown on YNB HIS- for 3 days. At the third try, we were able to observe around 20 colonies in our yeast transformation, about the same on the positive control and none on the negative control plate.

To verify our colonies we performed a genomic PCR using the TaKaRa PCR Amplification Kit, so we randomly chose eight clones from our transformation and one from the positive control plate (Figure 7).


Figure 7: Transformation verification: the expected size is 1.2kb.

All clones have the expected size (1.2kb), and the control where we inserted pRS313 does not show any band. We have successfully integrated tHmg1 and CrtE into the yeast using DPP1 homology sequence!

References

• S. cerevisiae genome, chromosome IV, DPP1 gene. GenBank: CP046084.1

Sequence and Features




Assembly Compatibility:

• 10
  INCOMPATIBLE WITH RFC[10]

  Illegal PstI site found at 50
  
• 12
  INCOMPATIBLE WITH RFC[12]

  Illegal PstI site found at 50
  
• 21
  COMPATIBLE WITH RFC[21]
• 23
  INCOMPATIBLE WITH RFC[23]

  Illegal PstI site found at 50
  
• 25
  INCOMPATIBLE WITH RFC[25]

  Illegal PstI site found at 50
  
• 1000
  COMPATIBLE WITH RFC[1000]