Composite
WT p5

Part:BBa_K2918028

Designed by: TUDelft2019   Group: iGEM19_TUDelft   (2019-09-27)
Revision as of 18:48, 19 October 2019 by Hafsaflats (Talk | contribs) (→‎Characterization of the SSB protein)


WT T7 promoter - Universal RBS - Φ29 SSB (p5) - WT T7 terminator

Sequence and Features


Assembly Compatibility:
  • 10
    COMPATIBLE WITH RFC[10]
  • 12
    COMPATIBLE WITH RFC[12]
  • 21
    COMPATIBLE WITH RFC[21]
  • 23
    COMPATIBLE WITH RFC[23]
  • 25
    COMPATIBLE WITH RFC[25]
  • 1000
    INCOMPATIBLE WITH RFC[1000]
    Illegal BsaI site found at 68
    Illegal BsaI.rc site found at 94

The construct is confirmed by sequencing and there are no mutations.

Overview

The replication of DNA and its conversion into functional proteins are vital processes in all living systems. DNA is copied during the replication process. The bacteriophage Φ29 contains a DNA replication machinery which replicates the linear plasmid by itself. This process is called orthogonal replication and can be beneficially used. The desired gene can be expressed in other hosts without interfering with the genome of its host. Our Sci-Phi 29 tool is based on the Φ29 DNA replication system and its four proteins. The terminal proteins (TP) cap the linear DNA, protect the linear DNA and are the primer for initiation of replication by the Φ29 DNA polymerase (DNAP/p2). DNAP binds to the TP and replicates the DNA. During the replication, single and double stranded DNA is protected by single stranded DNA binding proteins (SSB/p5) and double stranded DNA binding proteins (DSB/p6) respectively.

Strain Construction

Aim: To clone the WT T7 promoter, Universal RBS, P5 and T7 terminator in a level 1 MoClo backbone pICH47761
Procedure: The DNA sequence of the part was cloned with the following Basic parts: BBa_K2918007, BBa_K2918014, BBa_K2918002 and BBa_K2918015. The cloning protocol can be found in the protocol section of our website!

Characterization of the SSB protein

For expressing our constructs we used PUREfrex system. This is an E.coli based cell-free protein synthesis system and it contains all the elements to make in vitro translation-transcription possible. A 10-μL reaction consists of 5 μL feeding buffer, 0.5 μL enzyme solution, 1 μL ribosome solution, 5 nM DNA and RNAse-free milliQ for filling up the volume. For fluorescent labeling, 0.5 μL of BODIPY-Lys-tRNALys (FluoroTectTM GreenLys, Promega) was added, this binds to the translation products at the lysine residues sites.The proteins were identified by an 18% SDS-PAGE gel and mass spectrometry. From the 10-μL reaction, 8 μL was loaded on the SDS-PAGE while the other 2 μL was analysed by the mass spectrometer.

SDS-PAGE
After expressing the SSB protein for 3 hours, the sample was treated with RNAse (RNaseA Solution, Promega) for 30 minutes. To denaturate the protein the sample is also treated with 2x SDS loading buffer with 10 mM dithiotreitol (DTT) for 10 minutes at 90°C. Samples were loaded on a 18% SDS-PAGE (polyacrylamide gel electrophoresis) gel. Visualization was performed on a fluorescence gel imager (Typhoon, Amersham Biosciences) using a 488-nm laser and a band pass emission filter of 520 nm.

  • Figure 1: SDS-PAGE gels of DSB after protein purification. The gel features the ladder(L)

An SDS-PAGE was carried out for the SSB protein with 3 different promoter strengths: Wild-Type, 0.5 and 0.1. For a control PURE solution without any DNA was used. As can be concluded from the figure, in the sample containing the p5 protein a band indicated by the asterix can be found at the expected molecular weight(13kb). The band is also absent in the control, indicating that the p5 protein was successfully produced in the PURE system using this construct. The other band that can also be seen in the control could be due to contamination


Mass Spectrometry

Next to the SDS-PAGE, mass spectrometry was used to confirm the identity of the proteins. The mass spectrometer looks for the mass of peptide sequences, and the time it takes to detect them.these sequences are and the Dif To do this, a sequence unique to the SSB’s amino acid sequence were chosen and screened for their presence in the PURE system. For the p5 the peptide sequences are: IFNAQTGGGQSFK and TVAEAASDLIDLVTR. Data was normalized to the presence of the elongation factor EF-TU, which can be found in the same concentration across all PURE system solutions. The raw data and the optimized parameters for mass spectrometry method can be found
  • [[Media:transitionlist.xlshere ]]
</div>

actually it looks for mass of the peptide and then of some fragments. so it double identifies a peptide in two Mass-analyzers. First the peptide then it breaks it and analyzes the fragments which are again specific for that peptide dus als ik het goed begrijp: jij zegt tegen de mass spectrometer hey dit zijn massas van 2 peptide sequences het duurt zolang voor ze gemeten zijn en dan meet hij dus eerst de hele peptide die breekt en dan kijkt hij of de massas kan vinden van die 2 unieke sequences?

  • Figure 2A: Identification in mass spectrometry of one peptide (IFNAQTGGGQSFK) of p6 sample after purification
  • Figure 2B: Identification in mass spectrometry of one peptide (TVAEAASDLIDLVTR) of p6 sample after purification

The intensity of the mass spectrographs shown in Figure 2 only reflect the occurrence of a given sequence in the sample. The mass spectrometer looks for the peptide sequences that is selected. These peptide sequences were only present in the samples that were expected. The difference in height can be attributed to the strength of the promoters, less peptides were measured with decreasing strength. In conclusion, the results were positive and the identity of the proteins could be further confirmed by mass spectrometry.

In Vitro replication

Toxicity

Our Sci-Phi 29 tool is based on four components of the Φ29 bacteriophage: DNAP, TP, p5 and p6. However, overexpression of these proteins are toxic for the cell. In order to determine the optimal expression levels of the proteins in live cells, we carried out viability assays in E. coli BL21(DE3) pLysS. The results are shown in the graphs below.

  • Figure 3A: The growth curve of phi 29 p5 under a WT T7 promoter in hours with no IPTG induction
  • Figure 3B: The growth curve of phi 29 p5 under a WT T7 promoter in hours with 0.001 mM IPTG induction
  • Figure 3C: The growth curve of phi 29 p5 under a WT T7 promoter in hours with 0.01 mM IPTG induction
  • Figure 3D: The growth curve of phi 29 p5 under a WT T7 promoter in hours with WT mM IPTG induction
  • Figure 3E: The growth curve of phi 29 p5 under a WT T7 promoter in hours with 1 mM IPTG induction
  • Figure 3F: The growth curve of phi 29 p5 under a WT T7 promoter in hours with 10 mM IPTG induction
[edit]
Categories
Parameters
None