Part:BBa_K2933128

His+Linker a+Sumo+Linker b+CPS-1

This part encodes the fusion protein of His tag, sumo tag and CPS-1 to promote the expression and purification of target protein(CPS-1).

Sequence and Features

Assembly Compatibility:

• 10
  INCOMPATIBLE WITH RFC[10]

  Illegal EcoRI site found at 256
  Illegal PstI site found at 892
  
• 12
  INCOMPATIBLE WITH RFC[12]

  Illegal EcoRI site found at 256
  Illegal NheI site found at 33
  Illegal PstI site found at 892
  
• 21
  INCOMPATIBLE WITH RFC[21]

  Illegal EcoRI site found at 256
  Illegal BglII site found at 145
  Illegal BglII site found at 1174
  Illegal BamHI site found at 344
  
• 23
  INCOMPATIBLE WITH RFC[23]

  Illegal EcoRI site found at 256
  Illegal PstI site found at 892
  
• 25
  INCOMPATIBLE WITH RFC[25]

  Illegal EcoRI site found at 256
  Illegal PstI site found at 892
  Illegal AgeI site found at 793
  
• 1000
  COMPATIBLE WITH RFC[1000]

Usage and Biology

This composite part is made up with four basic parts, the His tag, the Sumo tag, three cutting sites(NdeI, NheI and BamHI) and our target protein CPS-1. It encodes a protein which is CPS-1 fused with His-Sumo tag. The fusion protein is about 45.2kD. In order to gain the highly purified target protein, we add His-Sumo tag in N-terminal of CPS-1 and combine the three parts with these three cutting sites. The fusion protein can be cut off at the cutting site BamHI. It is convenient for us to purify our target protein.

References

[1]Dereje Dadi Gudeta, Valeria Bortolaia,The Soil Microbiota Harbors a Diversity of Carbapenem-Hydrolyzing β-Lactamases of Potential Clinical Relevance[J]，Antimicrobial Agents and chemotherapy,January 2016

Molecular cloning

First, we used the vector pET28B-Sumo to construct our expression plasmid. And then we converted the plasmid constructed to E. coli DH5α to expand the plasmid largely.

Figure 1. a: The PCR result of CPS-1. b: The verification results by enzyme digestion.

After verification, it was determined that the construction is successful. We converted the plasmid to E. coli BL21(DE3) for expression and purification.

Expression and purification

Pre-expression:
The bacteria were cultured in 5mL LB liquid medium with ampicillin(100 μg/mL final concentration) in 37℃ overnight.
Massive expressing:
After taking samples, we transfered them into 1L LB medium and add antibiotic to 100 μg/mL final concentration. Grow them up in 37°C shaking incubator. Grow until an OD 600 nm of 0.8 to 1.2 (roughly 3-4 hours). Induce the culture to express protein by adding 1 mM IPTG (isopropylthiogalactoside, MW 238 g/mol). Put the liter flasks in 16°C shaking incubator for 16h.

Affinity Chromatography:
We used the Ni-sepharose to purify the target protein. The Ni-sepharose can combine specifically with the His tag fused with target protein.

• First, wash the column with water for 10 minutes. Change to Ni-binding buffer for another 10 minutes and balance the Ni column.
  
• Second, add the protein solution to the column, let it flow naturally and bind to the column.
  
• Third, add Ni-Washing buffer several times and let it flow. Take 5ul of wash solution and test with Coomassie Brilliant Blue. Stop washing when it doesn’t turn blue.
  
• Forth, add Ni-Elution buffer several times. Check as above.
  
• Fifth, collect the eluted proteins for further operation.
  

Anion exchange column:
According to the predicted pI of the protein and the pH of the ion-exchange column buffer, firstly select the appropriate ion exchange column (anion exchange column or cation exchange column). The pH of buffer should deviate from the isoelectric point of the protein. Since the isoelectric point of our protein is 5.88 in theory, we choose buffer pH of 7.4 and use anion exchange column for purification. The protein is concentrated with a 10KD concentration tube, and then the exchange buffer is used to exchange the protein to the ion-exchange liquid A. Finally, it is concentrated to less than 5ml by centrifuging at 4℃ and 3400rpm for 10 minutes in a high-speed centrifuge to remove insoluble substances and bubbles. Balance the selected column with liquid A. Through the AKTApure protein purification system, the samples are loaded to the column at a flow rate of 0.5ml/min, and continue washing for 5min. Gradually increase the content of liquid B in the column, change the salt concentration and then change the interaction between the sample and the column, and collect the corresponding eluent according to the position of the peak. Use SDS-PAGE to check the result.
The collected protein samples are concentrated in a 10 KD concentrating tube at a speed of 3400 rpm and concentrated for a certain time until the sample volume is 500 μl. At the same time, the superdex 200 column is equilibrated with a buffer to balance 1.2 column volumes. The sample is then loaded and 1.5 cylinders are eluted isocratically with buffer. Determine the state of protein aggregation based on the peak position and collect protein samples based on the results of running the gel.