Part:BBa_K1381017
CFY-X6 his
Colicin Fy The CFY is a bacteriocin in the colicin family. It is produced naturally by Y.frederiksenii and target close relatives to that bacteria. One among them is the Y.enterocolitica and our target pathogene. The Colicin Fy will target the cellmembrane of it's target.
The killing system We designed the killing system to secret the colicin Fy with the help of an export tag, the USP45 BBa_K1381018. This part will be without promoter, RBS and export tag. It only contains the colicin Fy and a 6x His-Tag for characterization. It is designed so that you can easily couple another promoter or export tag of your choice. This part contains the restriction sites NgoMIV att the start of the sequence to more easily fuse proteins like an export tag to it. Since it got a NgoMIV site att the start of the sequence it is possible to fuse other sequence if they follow the Freiburg Biobrick standard 25 and contains an AgeI site. However our part is not entirely built in the Freiburg standard Biobrick 25 since it does not contain an AgeI site.
Characterization
To be able to Characterize colicin Fy we had to couple it to a promoter and a RBS, this we did by creating the construct BBa_K1381023. To be able to see that colicin Fy was realy produced we needed to run a SDS-Page, but before we could do that we needed to purify the tests so that we only have our protein colicin Fy. Since the bacteriocin was designed with a histidine tag we could use an IMAC to purify it. after we had done this we could run thhe SDS-page gel.
LÄNK TILL PROTOKOL?
Figure 1: The gel contains the following from the left to the right
Protein ladder
Eluent 1 for lysate produced by bacteriocin producing bacteria
Eluent 3 for lysate produced by bacteriocin producing bacteria
Eluent 2 for lysate produced by bacteriocin producing bacteria
Final eluent test-tube 4 for lysate produced by bacteriocin producing bacteria
Final eluent test-tube 6 for lysate produced by bacteriocin producing bacteria
Eluent 2 for lysate produced by the negative control
Eluent 3 for lysate produced by the negative control
Final eluent test-tube 4 for lysate produced by the negative control
Final eluent test-tube 6 for lysate produced by the negative control
The results from the characterization experiments can be seen in figure 1. According to calculations based on the nucleotide sequence, the mass of colicin Fy is about 49,6 kDa. The protein ladder we used is Thermo Scientifics PageRuler Unstained Protein Ladder #26614. The thickest band is 50 kDa so our bands should be at about the same height.
Several IMAC and SDS pages were run, in all cases eluent 1 was found to be empty. This is not surprising because the eluent volume is so small that the proteins will not come out until eluent 2. Because of this we decided to skip eluent 1 for the negative control in the presented SDS in figure 4. Eluent 2 consists of several proteins, every protein that does not bind to the IMAC should come out in this step. Eluent 3 seems to be when our colicin Fy is eluted, seeing it shows a band at the correct length, 50kDa. The negative control did not show any band in 50kDa and expression could therefore be confirmed. Since the colicin was eluted at elution 3 no band can be seen at elution 4.
Sequence and Features
- 10COMPATIBLE WITH RFC[10]
- 12COMPATIBLE WITH RFC[12]
- 21COMPATIBLE WITH RFC[21]
- 23COMPATIBLE WITH RFC[23]
- 25INCOMPATIBLE WITH RFC[25]Illegal NgoMIV site found at 4
- 1000COMPATIBLE WITH RFC[1000]
| None |