Coding

Part:BBa_K3039003

Designed by: Ceilidh Welsh   Group: iGEM19_Exeter   (2019-08-29)
Revision as of 22:37, 21 October 2019 by ChloeS (Talk | contribs)


PETase S121E_D186H_R280A

Usage and Biology

The enzymes PETase and MHETase were first discovered in Ideonella sakaiensis in 2016 by a group of researchers in Japan. These enzymes were found to degrade polyethylene terephthalate (PET) into its monomers, terephthalic acid (TPA) and ethylene glycol (EG). PETase degrades PET into Mono-(2-hydroxyethyl)terephthalic acid (MHET), Bis(2-Hydroxyethyl) terephthalate (BHET) and TPA, the main product being MHET. MHET is further degraded by MHETase into TPA and EG. We are aiming to use mutants of these enzymes to degrade the microfibres that are coming off clothing during washing cycles.

This sequence is the Escherichia coli K12 (E. coli K12) codon optimized DNA of the S121E_D186H_R280A mutant of PETase, with an N-terminal His-tag. The His-tag was added to allow for conformation of expression and subsequent purification. The mutations have been reported in past papers to increase the thermostability of PETase and is therefore an improvement of the previous registry part BBa_K2010000.

The native predicted signal peptide (Met1-Ala33) was removed from the WT PETase sequence (Seo et al 2019) and replaced with a start codon (Met), however all mutations are numbered according to the full-length WT sequence. The amino acid sequence was submitted to Twist Bioscience who codon optimised the sequence for E. coli, ensuring that there were no forbidden restriction sites, to allow for potential cloning into alternative BioBrick plasmids. The resulting CDS was synthesised and cloned, by Twist, into pET28. This added a 63 AA His-tag and thrombin cleavage site to the N-terminal of the protein, a T7 promoter and T7 terminator.

Characterisation

In order to characterise our part and determine the rate of its activity and prove its functionality we have run a series of experiments. After transforming the Arctic Express, Rosetta Gami and BL21 DE3 strains of E. coli with our plasmid we induced the expression of the enzymes using IPTG. In order to confirm that the enzyme expression has been successful we ran a western blot which showed the presence of the enzyme in the soluble fractions of the sonicated cells. Afterwards the enzyme was purified and used in assays to show its functionality and determine the rate of its activity.



Expression in E.coli


Western blot of the soluble fraction of Arctic Express strain showing expression of all mutants. The PageRuler Plus prestained protein ladder was used and labeled with the corresponding sizes. The negative control is labeled with 1. This part (PETase S121E_D186H_R280A) is labeled with 4. A clear band is visible with a size of about 30 kDa which is the size of PETase with the His tag attached to it.

Western blot of the soluble fraction of Rosetta Gami strain showing expression of all mutants. The PageRuler Plus prestained protein ladder was used and labeled with the corresponding sizes. The negative control is labeled with 1. This part (PETase S121E_D186H_R280A) is labeled with 4. A clear band is visible with a size of about 30 kDa which is the size of PETase with the His tag attached to it.


Purification graphs

Nickel Affinity Chromatography


Nickel affinity column trace taken during initial purification of the enzyme. The light blue line shows the change in imidazole concentration with increasing volume run through the column and the purple line shows the corresponding change in A280 of eluent from the column. The peak at 48 ml shows protein elution


Size Exclusion Chromatography (Superdex-200)


Further purification of the enzyme by size exclusion chromatography using a calibrated Superdex-200 column. The large peak at an elution volume of ~95 ml shows the monomeric form of the protein



The esterase activity assay shows the production of p-nitrophenol (A405nm) at different substrate concentrations



The specific activity of the enzyme at differing substrate concentrations



Thermal Stability Graphs

Thermal Stability


The thermal stability assay shows the production of p-nitrophenol (A405nm) after the pre-incubation of the enzyme at increasing temperatures before the esterase assay was carried out.


Thermal Stability of BBa_K3039003 (PTS) Vs. Wild Type PETase


The % activity of the enzymes compared to the activity at room temperature. WT PETase is most active at 40 °C before immediately falling off to 0% activity at 50 °C. PETase S212E_D186H_R280A (PTS) is also most active at 40 °C but is able to retain ~70 % activity at 50 °C before falling to 0% activity at 60 °C. SP1and SP2 although are not as active at the lower temperatures but SP1 is able to retain ~35 % activity at 50 °C before falling to 0% activity at 60 °C.

Fibre Assay Graphs


The breakdown of PET fibres harvested from our filter into its constitutive parts with a change in enzyme concentration over a 76 hour period.

BHET Assay


The breakdown of PET fibres harvested from our filter into BHET with a change in enzyme concentration over a 76 hour period.

MHET Assay


The breakdown of PET fibres harvested from our filter into MHET with a change in enzyme concentration over a 76 hour period.

TPA Assay


The breakdown of PET fibres harvested from our filter into TPA with a change in enzyme concentration over a 76 hour period.

Conclusion

The enzyme is over expressed and found to be active in both the esterase assay as well as the being able to break down PET fibres collected as part of the washing machine filter. The enzyme is more thermal stable than the WT PETase retaining ~70 % activity at 50 °C. The enzyme was also the most active having a specific activity 1.3 x that of the WT PETase



===References=== [1] Hyeoncheol Francis Son, In Jin Cho, Seongjoon Joo, Hogyun Seo, Hye-Young Sagong, So Young Choi, Sang Yup Lee, Kyung-Jin Kim; Rational Protein Engineering of Thermo-Stable PETase from Ideonella sakaiensis for Highly Efficient PET Degradation (2019) ACS Catal. 9(4), 3519-3526 ===Sequences and Features=== BBa_K3039003 SequenceAndFeatures

[edit]
Categories
Parameters
None