Part:BBa_I746909:Experience

This experience page is provided so that any user may enter their experience using this part.
Please enter how you used this part and how it worked out.

Applications of BBa_I746909

2019 iGEM team Gunma Japan

2019 iGEM team Gunma Japanvalidated this part in BL21(DE3).

Fig.1 This is our Abs600 Standard Curve measured by PerkinElmer,Multipmode Plate Reader.

Fig.2 One colony of BE21(DE3)pSB1C3 BBa I746909 each from 2 plates were picked and cultured in 5 mL LB medium with 34 μL/mL Cam for 6.25 hours in falcon tubes. We conducted 2 biological and 4 technical replicates. Then these are diluted to be OD600 = 0.1.before added 500 μM IPTG.Abs600 and fluorescence of GFP were measured.All measurements went on under controlled temperature (25 ℃).

Fig.3 We also checked whether the colonies on plates are expressing GFP that derives from pSB1C3 BBa I746909 by directly putting 100 μM and 300 μM IPTG onto the colonies in hemisphere by pipettes.We note that this also means we could check the appropriate concentration for this time, for the teams who would look this later.After all we decided to add 500 μM IPTG into LB for liquid culture due to anxiety for deadline.

Fig.4 The plates were also observed under visible light.We spotted a strong light toward the plates for 10 sec in advance to emphasize the difference between them.

Fig.5 The BL21(DE3) in LB medium were also observed under visible light too. They were easily distinguished in room.

2018 iGEM team Linkoping Sweden

2018 iGEM team Linkoping Sweden validated this part.

The IPTG induction of BBa_I746909 was validated by expressing the protein in E. coli (BL21). Fluorescence was measured over 16 hours after IPTG induction and the bacteria was incubated at 37°C. Excitation was measured at 488 nm and emission at 510 nm. The optical density was measured at 600 nm. Different induction concentration of IPTG was used to stimulate the expression. Experiments were conducted in an infinite M1000 PRO plate reader. Graphs show the mean values of fluorescents per bacteria of 6 replicates. The error bars for Figure 2. represent the 95 % confidence interval. Results seem to indicate that 10 mM IPTG will give the most effective induction response and that the IPTG promoter is very sensitive. We make this statement from the fact that our smallest induction concentration (0,025mM) induced almost the same amount of fluorescence as our next strongest induction concentration (1mM).

Figure 1: The figure shows IPTG stimulation of the biobrick BBa_I746909 over 16 hours, the mesurments was carried out in a 96 well M1000 Pro plate reader at 37°C. Fluorescence was exited at 488 nm and emission was measured at 510 nm . Light scattering were excited at 600 nm.

Figure 2: The figure shows the end results after a 16 hour IPTG induction of BBa_I746909 at 37°C. The induction was carried out in a M1000 Pro plate reader. Fluorescence was excited at 488 nm and emission was measured at 510 nm . Light scattering was excited at 600 nm. The error bars represent a 95% confidence interval.

[http://2014.igem.org/Team:Imperial iGEM Team Imperial

We used this part as a template to make our own part (K1321337). We added Freiburg sites onto the existing sfGFP using overhang end primers during PCR. The part we made was sequence confirmed and showed very bright fluorescence, even when fused to our CBDs (cellulose binding domains).

[http://2014.igem.org/Team:Aachen iGEM Team Aachen

The iGEM Team Aachen used the biobrick I746909 to test their [http://2014.igem.org/Team:Aachen/Project/2D_Biosensor sensor chip technology].

Testing I746909 in sensor chips
I746909 in sensor chips induced with 2µl IPTG and measured with a plate reader. Top chip is not induced, bottom chip is induced with IPTG.

The biorbick I746909 was also used to test the measurement device [http://2014.igem.org/Team:Aachen/Project/Measurement_Device WatsOn].

Testing I746909 in WatsOn
I746909 in sensor chips induced with 2µl IPTG and measured with WatsOn. Left chip is not induced, right chip is induced with IPTG.

2015 iGEM team Bielefeld-CeBiTec

2015 iGEM team Bielefeld-CeBiTec used this part and improved it by addition of a designed, translation enhancing 5'-untranslated region (5'-UTR; BBa_K1758100). You can find further information at BBa_K1758102).

In vivo characterization of sfGFP with and without our designed, translation enhancing 5'-untranslated region (5'-UTR; BBa_K1758100). Relative fluorescence units were normalized on OD600. Error bars represent standard deviation of triplicates. PT7-sfGFP: BBa_I746909 (this part); PT7-UTR-sfGFP: BBa_K1758102

As can be seen in the picture, the difference was observable with the naked eye as well.

Comparision of cultures expressing sfGFP with the optimized UTR and without. Left: BBa_K1758102, right: BBa_I746909 (this part)