Part:BBa_K3939111

Fast degrading GFP

The ubiquitin tag is fused to the N-terminal of the GFP to make the GFP a rapidly degrading GFP

Sequence and Features

Assembly Compatibility:

• 10
  COMPATIBLE WITH RFC[10]
• 12
  COMPATIBLE WITH RFC[12]
• 21
  INCOMPATIBLE WITH RFC[21]

  Illegal BamHI site found at 277
  
• 23
  COMPATIBLE WITH RFC[23]
• 25
  INCOMPATIBLE WITH RFC[25]

  Illegal AgeI site found at 25
  Illegal AgeI site found at 466
  
• 1000
  COMPATIBLE WITH RFC[1000]

We improved the GFP part. In the beginning, we directly took the GFP part into practice, while later, it is observed that GFP has a relatively long half-life, which is not conducive to further measurement. This section we will illustrate how we test our improvel designs correspondingly, showing the reasonability in the process and the reliability of the results.

Measurement of nfGFP half-life

1. Characterization part design:

Ubiquitin is a small protein founded in all eukaryotes whose primary function is to label a protein to be quickly recognized and degraded by the proteasome in the cell. We added a ubiquitin tag before the GFP structural gene, predicting that this would result in faster recognition and degradation of the expressed ubiquitin-tagged-GFP fusion protein by the ubiquitin degradation mechanism [1]. To test our hypothesis, we designed the following parts and experiments.

Figure 1. The sketch map of the characterization plasmid of nfGFP

To avoid misunderstanding, we show the diffenences between two nfGFP parts in our project. When measuring the degradation rate of nfGFP, we used the inducible promoter Pgal and expressed it on a plasmid vector. In contrast, when verifying chromosome-free cell formation with nfGFP, the promoter is TDH3 which can express frequently, and we integrated it on the chromosome for expression by homologous recombination.

2. Experiment design:

Control group: S. Cerevisiae
Experimental material: S. Cerevisiae with a nfGFP expression plasmid
Before the induction, the cells were cultured and enriched in the medium for 15 hours. We measured the OD600 values and the nfGFP fluorescence values. When the nfGFP fluorescence signals reached a steady value, we stopped inducing, then changed cells to standard medium. Considering the end of induction as time zero, we recorded the changes of OD600 and nfGFP fluorescence signals every two hours. Due to the shutdown of nfGFP expression in the cell, the cells can no longer produce reporter proteins, so the change in fluorescence signal intensity since then roughly reflects the degradation rate of nfGFP. By measuring the nfGFP fluorescence values, we plotted the degradation curves of nfGFP and calculated the half-life of nfGFP.

3. Experiment operation

(1) Enrichment and induction: Due to a large amount of culture medium required for subsequent measurements, we used shake flasks with 25 ml of induction medium to minimize the effect of the volume changes of the culture medium.
(2) Measurement of OD600: We used a UV spectrophotometry to measure OD600. To ensure data reliability, we unified the dilution multipliers while ensuring that the values are between 0.1-1.0 and as far as possible between 0.2-0.8.
(3) Measurement of fluorescence value: We use a Microplate Reader to measure the nfGFP fluorescence value. After the OD600 measurement, we wash off the culture medium and resuspend the cells with sterile water. Then, add 200 μl of the suspension to be measured to each well of the 96 well microtiter plate. We set blank reference (water), control groups and experimental groups in three parallel groups when adding samples. The excitation/emission light wavelength of nfGFP in the Microplate Reader was 488/535 nm.

4. How we analyze and process data

Since the sample is diluted, the fluorescence intensity is equal to the measured fluorescence intensity multiplied by the dilution factor. Besides, the measured fluorescence intensity value should also subtract the blank value. In summary, the formula for calculating the nfGFP fluorescence intensity should be as follows.

V^'=ω*(V-C)

V^':the true fluorescence intensity of nfGFP/200μl sample
V: the measured value of nfGFP fluorescence signal/200μl sample
C: blank reference(water)
ω: the dilution factor of sample
The values of the three parallel groups of samples were averaged and plotted, the calculated data are shown in the figure.We use the following formula to fit the measured value and calculate the half-life value.

N=N_0*e^(-kt)

τ=ln2/k

N: fluorescence measurement over time
N_0: initial fluorescence value
τ: half life value

Figure 2. The degradation curve of nfGFP