Part:BBa_K2918040

Cross-species based iFFL

Genetic implementation of an incoherent feed forward loop (iFFL) in which a stabilized 0.1 T7 promoter is controlling GFP expression.

Sequence and Features

Assembly Compatibility:

• 10
  INCOMPATIBLE WITH RFC[10]

  Illegal PstI site found at 283
  Illegal PstI site found at 2538
  
• 12
  INCOMPATIBLE WITH RFC[12]

  Illegal PstI site found at 283
  Illegal PstI site found at 2538
  
• 21
  INCOMPATIBLE WITH RFC[21]

  Illegal XhoI site found at 250
  Illegal XhoI site found at 3383
  
• 23
  INCOMPATIBLE WITH RFC[23]

  Illegal PstI site found at 283
  Illegal PstI site found at 2538
  
• 25
  INCOMPATIBLE WITH RFC[25]

  Illegal PstI site found at 283
  Illegal PstI site found at 2538
  Illegal AgeI site found at 1277
  
• 1000
  COMPATIBLE WITH RFC[1000]

The two transcriptional units in this composite part are oriented outwards.

Usage and Biology

A Incoherent feed-forward loop (iFFL) is a unique control systems motif where the output signal is robust to changes in the input signal. This is achieved by the introduction of a repressor.

• 

  Figure 1: Overview of incoherent feed-forward loop

iFFL can be applied to genetic circuits to achieve expression independent from copy number, transcriptional and translational rates. To implement the iFFL in a genetic circuit, TALE proteins can be used. These proteins consist of repeats where 12th and 13th amino acids can vary, these are called the repeat variable diresidue (RVD). RVDs have been shown to bind to DNA in a simple one-to-one binding code (Doyle, Stoddard et al., 2013). The direct correspondence between amino acids allows scientists to engineer these repeat regions to target any sequence they want. In our system, we used the TALE protein as a repressor by engineering promoters to contain the binding site of this specific TALE protein (0.1 T7sp1 promoter, 0.5 T7sp1 promoter and P_BHRsp1 promoter).
In our genetic circuit, a unrepressed promoter controls the expression of TALE protein while the promoters with the TALE binding sites drive expression of GFP.

• 

  Figure 2: Overview of how the TALE proteins represses GFP

When transcriptional units are placed in series due to low effieciency of terminators, leaky expression of the gene in the neighbouring transcriptonal unit can occur. This significantly influences the behavior of the iFFL genetic circuit (Segall-Shapiro et al., 2018). Hence, the transcriptional units in the circuit are oriented outward to achieve insulation from influence of the neighboring transcriptional unit.

An interesting application of the iFFL is to achieve controllable gene expression across different bacterial species. Gene expression in different bacterial contexts is influenced by changes in copy number, transcriptional and translational rates. To achieve expression robust to changes in transcriptional and tranlational rates, the ratio of transcriptional and translational rates of GFP and repressor need to be constant. This can be achieved by using orthogonal T7 promoter and its variants (T7 promoter, 0.5 T7 promoter,0.1 T7 promoter, 0.5 T7sp1 promoter and T7sp1 promoter ).

Apart from being able to achieve stable gene expression across different bacterial species, it is necessary to attain different levels of gene expression. The T7 promoter based optimized iFFL can be used to obtain higher levels of gene of interest (GFP) expression as the expression of TALE is driven by a lower strength promoter (0.1 T7 promoter) compared to the promoter (0.5 T7sp1 promoter) driving GFP expression.

Strain Construction

The construct was assembled by golden gate assembly based modular cloning system. First, the individual transcriptional units were cloned into level 1 destination vectors pICH47761 and pICH47822 by BpiI based golden gate assembly. The multi-transcriptional unit construct was assembled by a BsaI based golden gate. The assembly was a one-pot restriction-ligation reaction where the individual level 1 constructs were added along with the destination vector pICH48055. The correct clone was distinguished by blue-white screening and the construct was confirmed by sequencing. The cloning protocol can be found in the MoClo section below.

Modular Cloning

Modular Cloning (MoClo) is a system which allows for efficient one pot assembly of multiple DNA fragments. The MoClo system consists of Type IIS restriction enzymes that cleave DNA 4 to 8 base pairs away from the recognition sites. Cleavage outside of the recognition site allows for customization of the overhangs generated. The MoClo system is hierarchical. First, basic parts (promoters, UTRs, CDS and terminators) are assembled in level 0 plasmids in the kit. In a single reaction, the individual parts can be assembled into vectors containing transcriptional units (level 1). Furthermore, MoClo allows for directional assembly of multiple transcriptional units. Successful assembly of constructs using MoClo can be confirmed by visual readouts (blue/white or red/white screening). For the protocol, you can find it here.

Note: The basic parts sequences of the Sci-Phi 29 collection in the registry contain only the part sequence and therefore contain no overhangs or restriction sites. For synthesizing MoClo compatible parts, refer to table 2. The complete sequence of our parts including backbone can be found here.

Table 1: Overview of different level in MoClo

Level	Basic/Composite	Type	Enzyme
Level 0	Basic	Promoters, 5’ UTR, CDS and terminators	BpiI
Level 1	Composite	Transcriptional units	BsaI
Level 2/M/P	Composite	Multiple transcriptional units	BpiI

For synthesizing basic parts, the part of interest should be flanked by a BpiI site and its specific type overhang. These parts can then be cloned into the respective level 0 MoClo parts. For level 1, where individual transcriptional units are cloned, the overhangs come from the backbone you choose. The restriction sites for level 1 are BsaI. However, any type IIS restriction enzyme could be used.

Table 2: Type specific overhangs and backbones for MoClo. Green indicates the restriction enzyme recognition site. Blue indicates the specific overhangs for the basic parts

Basic Part	Sequence 5' End	Sequence 3' End	Level 0 backbone
Promoter	NNNN GAAGAC NN GGAG	TACT NN GTCTTC NNNN	pICH41233
5’ UTR	NNNN GAAGAC NN TACT	AATG NN GTCTTC NNNN	pICH41246
CDS	NNNN GAAGAC NN AATG	GCTT NN GTCTTC NNNN	pICH41308
Terminator	NNNN GAAGAC NN GCTT	CGCT NN GTCTTC NNNN	pICH41276

References

• Lou, C., Stanton, B., Chen, Y.-J., Munsky, B., & Voigt, C. A. (2012). Ribozyme-based insulator parts buffer synthetic circuits from genetic context. Nature Biotechnology, 30(11), 1137–1142.