Part:BBa_K349001
RFP-AB-BsaI (for construction of AB BioBytes 2.0)
This is the RFP BsaI AB Base plasmid v.2 for the construction of components of the BioBytes 2.0 assembly method. The RFP cassette can be removed using the BsaI enzyme and a new AB BioByte may be inserted into the plasmid for amplification.
RFP-AB-BsaI (for construction of AB BioBytes 2.0)
This is the RFP BsaI AB Base plasmid v.2 for the construction of components of the BioBytes 2.0 assembly method. The RFP cassette can be removed using the BsaI enzyme and a new AB BioByte may be inserted into the plasmid for amplification.
Usage and Biology
This plasmid is a useful tool for creating BioBytes 2.0 parts. To create a new part PCR the part of interest, incorporating BsaI cut sites with appropriate overhangs onto each side. Then, cut this Base Plasmid v.2 and the PCR product with BsaI. Ligate it together. Again, because the overhangs are unique, the plasmid backbone can not re-ligate without an insert. The insert can only be the new part of interest, or the RFP coding cassette that was originally in the base plasmid, leading to a total of 2 possible ligation products. When transformed, the ligation products can appear red (if the original RFP cassette is reinserted) or white (if the part of interest is inserted). This provides a selection method for plasmids that have the part of interest in it.
Biobytes 2.0 Assembly Protocol:
This part is compatible with the Team Alberta 2010 Biobytes 2.0 assembly method. When digested with BsaI and purified, it can yield an AB RFP cassette. It can also be used to make other AB bytes as per the process described above. The following protocol outlines the Biobytes 2.0 assembly method:
1) Mix the iron micro beads for 10 minutes.
2) Transfer 20 ul of iron micro beads to a 1.5 mL tube.
3) Pull the beads to the side using a magnetic tube rack.
4) Remove and discard the supernatant.
5) Add 50 ul of BioBytes 2.0 Wash Buffer to the beads. Flick gently to resuspend.
6) Pull the beads to the side using a magnetic tube rack.
7) Remove and discard the supernatant.
8) Repeat steps 5 to 7.
9) Add 200 ng of a premade anchor-Byte construct (premade in the GENOMIKON kit) to the beads and top off the volume to 20ul with TE Buffer. Flick gently to resuspend.
10) Allow annealing for 30 minutes, mixing by flicking every 5 minutes. Ensure that there are no droplets on the sides of the tube.
11) Repeat steps 6 and 7.
12) Repeat steps 5 to 7.
13) Add 200 ng of the next BioByte of your construct, making sure that a BA Byte follows an AB Byte and vice versa. Add an appropriate amount of 2x QuickLigase Buffer, Quick Ligase and TE to a total volume of 20ul.
14) Flick gently to resuspend. Allow ligation for five minutes, flicking gently every minute.
15) Add 30ul of Wash Buffer to the tube. Flick gently.
16) Repeats steps 6 and 7.
17) Repeat steps 5 to 7 twice.
18) Repeat steps 13 to 17 for each subsequent Byte addition, including the last BioByte.
19) After the last Byte has been ligated and washed, add 30 ul of 75C Elution Buffer. Keep at 75C for 10 minutes.
20) After 10 minutes, still at 75C, put the tube into a magnetic rack . Allow the beads to be pulled aside and collect the supernatant into a clean 1.5 mL tube. The supernatant will contain your construct.
For more information on this construction method click here
Sequence and Features
- 10COMPATIBLE WITH RFC[10]
- 12COMPATIBLE WITH RFC[12]
- 21COMPATIBLE WITH RFC[21]
- 23COMPATIBLE WITH RFC[23]
- 25INCOMPATIBLE WITH RFC[25]Illegal AgeI site found at 792
Illegal AgeI site found at 904 - 1000INCOMPATIBLE WITH RFC[1000]Illegal BsaI site found at 1
Illegal BsaI.rc site found at 1086
| n/a | RFP-AB-BsaI (for construction of AB BioBytes 2.0) |