Difference between revisions of "Part:BBa K389016:Experience"

Latest revision as of 00:36, 28 October 2010

This experience page is provided so that any user may enter their experience using this part.
Please enter how you used this part and how it worked out.

Applications of BBa_K389016

Growth functions and mRFP expression for BBa_K389016

To characterize this part we performed several cultivations with different concentrations of [http://www.chemblink.com/products/2478-38-8.htm acetosyringone] as inducer and measured the fluorescence emitted by mRFP (Protocol). We used Escherichia coli DB3.1 carrying the pSB1C3::K389016 plasmid. Even without inducer the bacteria carrying the plasmid showed decelerated growth. In addition acetosyringone affected the growth rates (we used a stocksolution of 20 mM acetosyringone solved in 10 % (v/v) DMSO). Growth curves, averaged specific growth rates and doubling times are shown below. It can be observed, that E. coli carrying the pSB1C3::K389016 plasmid growths nearly linear.

The specific growth rates µ and doubling times t_d are calculated with the OD₆₀₀ and following formulas:

Exemplary induction curves with the fluorescence normalized to OD₆₀₀ are shown in fig. 2. We observed a basal transcription, but the induction with acetosyringone is undoubtedly. The detailed data analysis and transfer function is described below.

Transfer function of BBa_K389016

The data for the transfer function was measured and analyzed as described below. Nelson et al suggests using a dose response function and fitting it with a logistical equation for the data analysis of receptor systems ([http://www.nature.com/nature/journal/v416/n6877/abs/nature726.html Nelson et al., 2002]). The data was fitted with a function of the form

with the Hill coefficient p, the bottom asymptote A1, the top asymptote A2 and the switch point log(x₀). Figure 3 shows the measured normalized specific production rates q_P,n (eq. 10) plotted against the logarithm of the concentration of the inductor [http://www.chemblink.com/products/2478-38-8.htm acetosyringone] in µM. The fit has an R² = 0.99.

The important data from the transfer function is summarized in table 2:

So the fully induced VirA/G signaling system has a 2.6 fold increased expression compared to the uninduced system. The Hill coefficient is > 1, so a positive cooperation can be observed ([http://www.sciencedirect.com/science?_ob=ArticleURL&_udi=B6WMD-4V42JG5-1&_user=10&_rdoc=1&_fmt=&_orig=search&_sort=d&_docanchor=&view=c&_acct=C000050221&_version=1&_urlVersion=0&_userid=10&md5=b6431553217aca1129c5b441f4b78425 D Chu et al., 2009]). The switch point of the system is at about 25 µM, so this is the concentration at which the device output is 50 % of the maximum output.

Data analysis for BBa_K389016

The data analysis is made in three steps. First step is the processing of the fluorescence raw data gained by the fluorescence plate reader for every sample:

In the second step the RFU_corrected of every sample is plotted against the cultivation time it was drawn. The data is fitted by an exponential fit of the following style:

The accumulation of mRFP in the cells is always exponential. A typical fitted product accumulation curve is shown below:

Fig. 4: Exponential fit on the measured RFU_corrected plotted against cultivation time in h of a cultivation of BBa_K389016 in E. coli DB3.1 in LB medium with 10 mg ml^-1 chloramphenicol and 150 µM acetosyringone.

The product accumulation in a cultivation can be described as:

with the amount of product P, the cell count X and the specific production rate q_P.

RFU is commensurate to the concentration of mRFP (P) and the OD₆₀₀ is commensurate to the cell count (X) ( Canton and Labno, 2004):

With these assumptions it is possible to calculate the specific production rate of mRFP q_P in the third step: the specific production rate for every sample of a cultivation is calculated by the derivation of the exponential fit line which describes the accumulation of product in the culture (dRFU/dt) and the measured OD₆₀₀ data:

The specific production rates q_P of all samples of all cultivations made with a specific inducer concentration c are averaged and normalized against the specific production rate of the uninduced system q_P,0:

This normalized specific production rate we calculated is commensurate to relative promotor units (RPU) which is commensurate to PoPS (polymerase per seconds) (Canton and Labno, 2004; Pasotti et al., 2009):

Plasmid conformation analysis

A plasmid conformation analysis for the BioBrick BBa_K389016 in pSB1C3 was performed by the [http://web.plasmidfactory.com/de/ PlasmidFactory] by Capillary Gel Electrophoresis (CGE). The chromatogram is shown in fig. 5 and the results in tab. 3. The data shows a high percentage of covalently closed circular (ccc) plasmid DNA. This is the biological active shape of plasmids so a high percentage of ccc plasmid DNA indicates a high quality of plasmid DNA ([http://web.plasmidfactory.com/en/service_CGE.html PlasmidFactory]).

Different possible inducers

A list of tested possible inducers for a VirA/G signaling system is shown in tab. 4. These inducers where tested as a mix. The specific production rate of mRFP q_P measured as described above for the mix did not significantly differ from the synthesis rate of the uninduced system (t-Test, p < 0.005). So none of the possible inducers listet in tab. 4 induce the VirA/G signaling system significantly in the measured concentration range. In tab. 4 the chemical structures of the tested possible inducers are shown, too. Acetosyringone is also in tab. 4 although it was not tested in the inducer mix to show the chemical similarity of the tested possible inducers to the natural inducer of the VirA/G signaling system.

Table 4: Tested possible inducers for a VirA/G signaling system and acetosyringone with concentrations and chemical structure that were tested.

Inducer	Concentration / µM	Chemical structure
Capsaicin	200
Dopamine	200
Homovanillic acid	200
3-Methoxytyramine	200
Acetosyringone	200

Protocols

Cultivation

• Inoculate 10 mL LB containing desired antibiotic with glycerol stock

• Cultivate over night at 37 °C and 175 rpm

• Measure the OD₆₀₀

• Prepare shake flasks with LB, antibiotic and different concentrations of the inducer acetosyringone
  • For mRFP measurement at least 20 mL starting volume

• Inoculate the main culture with a starting OD₆₀₀ of 0.1

• Cultivate at 37 °C and 175 rpm

• Take a sample at least every hour and measure the OD₆₀₀

Measurement

• Take at least 500 µL sample for each measurement (200 µL is needed for one measurement) so you can perform a repeat determination

• Freeze samples at -80 °C for storage

• To measure the samples thaw at room temperature and fill 200 µL of each sample in one well of a black, flat bottom 96 well microtiter plate (perform at least a repeat determination)

• Measure the fluorescence in a platereader (we used a Tecan Infinite® m200 platereader ) with following settings
  • 20 sec orbital shaking (1 mm amplitude with a frequenzy of 87.6 rpm)
  • Measurement mode: Top
  • Excitation: 584 nm
  • Emission: 620 nm
  • Number of reads: 25
  • Manual gain: 150
  • Integration time: 20 µs

References

Canton B and Labno A (2004) Data processing of Part BBa_F2620.

Chu D, Zabet NR, Mitavskiy B (2009) [http://www.sciencedirect.com/science?_ob=ArticleURL&_udi=B6WMD-4V42JG5-1&_user=10&_rdoc=1&_fmt=&_orig=search&_sort=d&_docanchor=&view=c&_acct=C000050221&_version=1&_urlVersion=0&_userid=10&md5=b6431553217aca1129c5b441f4b78425 Models of transcription factor binding: Sensitivity of activation functions to model assumptions], J Theor Biol 257(3):419-429.

Greg Nelson, Jayaram Chandrashekar, Mark A. Hoon, Luxin Feng, Grace Zhao, Nicholas J. P. Ryba & Charles S. Zuker (2002) [http://www.nature.com/nature/journal/v416/n6877/abs/nature726.html An amino-acid taste receptor ], Nature 416: 199-202.

Pasotti L, Zucca S, Del Fabbro E (2009) Characterization experiment on BBa_J23100, BBa_J23101, BBa_J23118, https://parts.igem.org/Part:BBa_J23101:Experience.

[http://web.plasmidfactory.com/en/service_CGE.html PlasmidFactory]

User Reviews

UNIQ750ece84db60e6b2-partinfo-00000014-QINU UNIQ750ece84db60e6b2-partinfo-00000015-QINU