Part:BBa_J73019
Added by XHD-Wuhan-China
We first examined the efficiency of the BBa_J73019 cu promoter. Then BBa_J73019 cu promoter BBa_K1755001 (ribB coding sequence) was made into BBa_K4172001.
We do parallel validation for BBa_J73019 and BBa_K4172001, respectively. The experimental results show that the effect of BBa_J73019 is significantly improved compared with BBa_K4172001.
Evaluation on copper ion dependence of pcutR
Biobrick-compatible restriction site sequence was introduced into pET-23b (+) plasmid by inactivation kinase ligation kit, and named pLZ01 for standard component assembly. We synthesized a copper-sensitive promoter by DNA synthesis and named it pcutR.
Escherichia coli BL21 carrying plasmid pLZ01-pcutR-GFP was cultured overnight at 160rpm in a shaking table at 37℃. The cultured Escherichia coli was inoculated in solutions containing different concentrations of copper ions (0, 0.05, 0.2, 0.5, 1, 1.2 mM) for 4 hours. Then, the fluorescence intensity of GFP (excitation wavelength: 490 nm; emission wavelength: 510 nm) and OD600 of Escherichia coli BL21 carrying plasmid pLZ01-pcutR-GFP were measured by microplate reader. The average GFP/cell was calculated by dividing the original fluorescence intensity by OD600. In order to observe the expression of GFP in cells induced by copper ion, the culture was centrifuged (5000 g, 5 min, 4℃) and suspended again in PBS buffer (10 mM, pH 7.4) after 4 hours of culture. Fluorescence imaging was performed on a fluorescence microscope (Olympus, Japan) using a 40-fold objective lens.
The results showed that copper ion could initiate the expression of green fluorescent protein GFP in copper sensitive promoter pcutR, and the initiation degree of copper sensitive promoter pcutR was linearly related to copper ion concentration
Working system verification
We synthesized ribB gene by DNA synthesis. The recombinant plasmid pLZ01-pcutR-ribB was transferred to Escherichia coli BL21 for expression.
A two-chamber MFC reactor with a working volume of 240 mL was set up, and the electrodes were pretreated before use. Carbon felt with an area of 16cm2 was used as anode and cathode. These electrodes are connected by titanium wires to an external resistor of 1000 Ω.
In MFC operating system, different concentrations of Cu2+ (0-500μM) were added to the anode medium in M9 liquid medium for Cu2+ response regulator use. The cathode solution was potassium ferricyanide (100 mM potassium ferricyanide in 50 mM phosphate buffer, pH 7.0). Voltage was recorded at 10 min intervals in an MFC biosensor using a data acquisition device
The results showed that the expression of ribB gene promoted electron transfer and eventually led to a significant increase in MFC voltage, and there was a linear relationship between ribB concentration and MFC voltage
Copper Biosensor
This sensor will be used in a cell-free protein biosynthesis system to detect copper in solution. The part uses the pCusC promoter which is sensitive to copper via the E. coli CusS/CusR two component system. The promoter responds directly to the CusR cytoplasmic response regulator which is activated by a transmembrane histidine kinase enzyme CusS found in the cell membrane. A standard ribosome binding site was added to the composite device after the promoter. Green fluorescent protein (GFP) was chosen as the reporter protein to visualize the presence of copper in water samples. The composite ends with a double terminator.
Sequence and Features
- 10COMPATIBLE WITH RFC[10]
- 12COMPATIBLE WITH RFC[12]
- 21COMPATIBLE WITH RFC[21]
- 23COMPATIBLE WITH RFC[23]
- 25COMPATIBLE WITH RFC[25]
- 1000INCOMPATIBLE WITH RFC[1000]Illegal BsaI.rc site found at 767
| None |