Part:BBa_K540000
rcn-csgBAEFG, over-induces adherence in response to cobalt
This part associates the rcn promoter, whose expression increases with cobalt in the medium, with csgBAEFG, an operon that enables the production and secretion of curlis, which are adherent proteins. It contains the necessary RBS to work.
With this part, strains can become adherent in response to cobalt in the medium.
This part may also make bacteria adherent in response to nickel, which has however not been studied.
Characterization
Following results show that this part increase the adherence ability of the transformed strain. The presence of Cobalt enhance the adherence and this response seems to be proportional to the concentration of cobalt (Cobalt range : 10µM to 100µM)
In our plasmid collection described in the wiki, this part is named piG2 in the backbone Amp
and piG25 in the backbone Cm. The negative control, which correspond to it, is the plasmid
PUC18 and it is named piG6 in the backbone Amp.
We worked with the plasmid piG2 for the tests and we tried three different genetic
backgrounds : the strain NM522 to optimize the experimental conditions, the strain MC4100
to test the effect of a range of concentrations in Cobalt and the chromosomically GFP tagged strain MG1655.
For this last strain, we’d like to thank Mrs Chun Chau Sze from the NTU Laboratory who gave
us the fluorescent strain and allowed us to use it for our experiment in the iGEM competition.
You can find his work in the following publication: J Microbiol Methods. 2009 Feb;76(2):109-19. Epub 2008 Sep 24.
Microscopy tests
We realized a first test in a MC4100 fluorescent strain whose fluorescence had been acquired
by the introduction of the plasmid p150 containing a GFP. However, we obtained incoherent results and we
had some doubts about the stability of this plasmid.
As a chromosomical GFP tag would be more reliable, these microscopy assay have been done with the MG1655 strain.
We constructed the two following strains:
- MG1655/piG2 (AmpR)-> STRAIN with the part Prcn-csgBAEFG
- MG1655/piG6 (AmpR)-> NEGATIVE CONTROL
We started a first test in M63G medium. In sterile empty plates, we introduced 10mL of
M63G, we added 100μL of Amp and 100μL of bacteria from a saturated liquid culture.
Finally, we added 3 or 4 sterile glass slides and incubated at 30°C for 23 hours.
We then observed the biofilms formed at the surface of the slides with a fluorescent
microscope. Several sites in the slides were photographed, the best pictures are presented
here.
We can easily see that the presence of the part (strain with piG2) increase the adherence ability of the strain.
We then determined the effect of a range of concentrations in Cobalt on the adherent strain.
For this, we realized another test, using the same strains, the same medium and the same
protocol.
Time of incubation was shorter (15 hours) in order to see perfectly the effect of Cobalt on the
strain. The range of concentrations in Cobalt was: 0 and 10μM for the negative control and 0,
10, 25, 50, 100μM for the strain adherent.
Again, several sites in the slides were photographed and we present here the best pictures.
With these observations, we concluded that the adherence increases with the Cobalt concentration from 0μM up to 25μM. For concentrations above 25μM, the effect of the cobalt is not visible anymore.
After these first qualitative results, we wanted to quantify the effect of Cobalt on the part. As we didn’t have a confocal microscope, we started adherence tests in 24 well plates.
Quantitative adherence tests in plates
Useful development to choose the best adherence test conditions are discribed in the experiences tab
MC4100 bacteria have been transformed with the Prcn-csgBAEFG part.
We constructed the two following strains:
- MC4100/piG2 (AmpR)-> STRAIN with the part Prcn-csgBAEFG
- MC4100/piG6 (AmpR)-> NEGATIVE CONTROL
In the following experiment, we are testing both the effect of this part on the bacteria, and the response to cobalt with and without the added part.
24-well plates have been seeded by both strain, with increasing cobalt concentration. This experiment has been repeated several times, by different students. Total OD measurement shows the relative growth of the bacteria in the different well, while the OD measurement of the fixed fraction of bacteria will reveal the effect of the part on biofilm formation.
Squares, triangles and diamonds represent the 3 replicates done for this experiment
These results demonstrate that total OD does not vary significantly with different medium conditions.
This implies that adding the part, or cobalt in the medium does not impact the growth of the tested bacteria, and that differences in OD between wells will be significant.
Squares, triangles and diamonds represent the 3 replicates done for this experiment
From the graph above, we can draw 2 conclusions :
Conclusion: this part creates in new effect in transformed bacteria : cobalt makes them produce curli, in turn increasing their overall adherence.
Safety
This part is not toxic by itself. However, when using this part, you will probably need to handle cobalt. Cobalt is toxic in all its forms ( ionic or metallic ) by inhalation, ingestion or contact. Wear adapted personal protection equipment ( labcoat, safety glasses, safety gloves ) and dispose of it in appropriate waste containers.
Usage and Biology
This part was designed to be used in a strain with enhanced cobalt capture capacities ( like the one described in [1]). That way, the strain captures cobalt in the medium and becomes adherent, which allows it to be easily separated from the medium. Possible applications include bioremediation of radioactive cobalt in nuclear power plants, using this adherence property to build a biofilter.
[1] Bioremediation of trace cobalt from simulated spent decontamination solutions of nuclear power reactors using E. coli expressing NiCoT genes. Raghu G, Balaji V, Venkateswaran G, Rodrigue A, Maruthi Mohan P. Appl Microbiol Biotechnol. 2008 Dec.
Sequence and Features
- 10COMPATIBLE WITH RFC[10]
- 12COMPATIBLE WITH RFC[12]
- 21INCOMPATIBLE WITH RFC[21]Illegal BglII site found at 47
- 23COMPATIBLE WITH RFC[23]
- 25INCOMPATIBLE WITH RFC[25]Illegal AgeI site found at 2108
- 1000COMPATIBLE WITH RFC[1000]
| None |