Part:BBa_K516132:Experience

This experience page is provided so that any user may enter their experience using this part.
Please enter how you used this part and how it worked out.

User Reviews

SCU-China 2018: We use the BBa_K516132 as an original source of the mRFP for our part spacer J23101-RFP(BBa_K2611003)<a href="https://parts.igem.org/Part:BBa_K2611001">BBa_K2611003</a>

UNIQd267ebbbf967645c-partinfo-00000000-QINU UNIQd267ebbbf967645c-partinfo-00000001-QINU

UNIQd267ebbbf967645c-partinfo-00000002-QINU

••••• UNIPV-Pavia iGEM 2011

NB: unless differently specified, all tests were performed in E. coli MGZ1 in M9 supplemented medium at 37°C in low copy plasmid pSB4C5. Used to quantify promoter strength (relative to BBa_J23101 with RBS B0034) and the RBS efficiency. Characterized together with: BBa_J23101 J23101-RBS34-mRFP-TT BBa_K516130 J23101-RBS30-mRFP-TT BBa_K516131 J23101-RBS31-mRFP-TT BBa_J23101 is the reference standard promoter for the computation of RPUs. As discussed in 'data analysis' section, RPUs are relative units for the evaluation of promoter strength, based on a mathematical model of the transcription and the translation of a reporter gene. The RPUs are supposed to be indepedent on the experimental setup, provided that the reference standard BBa_J23101 must be assayed in the same experimental condition of the studied promoter. It means that if the studied promoter is in a low copy number plasmid and drives the expression of a reporter protein P, J23101 must be assembled in the same vector upstream of the same reporter P. This approach is in accordance with the philosophy of synthetic biology, based on the concept of 'modularity' of the components. According to this approach, the assembly of basic well characterized modules to build complex circuits allows the prediction of the circuit behavior starting from the knowledge on the basic parts. Salis et al. [Nat Biotec, 2009] stated that 'Identical ribosome binding site sequences in different genetic contexts can result in different protein expression levels' and again 'It is likely that this absence of modularity is caused by the formation of strong secondary structures between the RBS-containing RNA sequence and one protein coding sequence but not another.' For this reason, RPUs might not be reliable when comparing the same promoter with different RBSs because of the un-modularity of the RBS. In order to asses what's the effect of RBS 'un-modularity' on RPUs reliability, we have built a set of four constitutive promoters (BBa_J23101) followed by one of the four RBSs tested. These parts were used to evaluate RBS efficiency. Data were collected and analyzed as described in 'Measurements' and 'Data analysis' sections. RPUs and Synthesis rate per cell [AUr] were computed and results are summarized in the table below. NB: in the RPU computation, the J23101-RBS34-mRFP-TT (BBa_J23101) in low copy plasmid pSB4C5 construct has been considered as the reference standard. With this assumption, RPUs are identical to the estimated RBS efficiency. Data are provided as average [Standard error]. J23101 promoter with RBS Scell R.P.U.s RBS30 122 [13.23] 2.45 [0.27] RBS31 2 [0.25] 0.04 [0.01] RBS32 20 [1.7] 0.40 [0.03] RBS34 50 [1.87] 1 [0.02] On the other hand, if the hypothesis of RBS modularity depending on the promoter is accepted, the J23101-RBSx series we have provided can be used as a library of ready-to-use reference standard for RPU evaluation, that allows to depurate RPU measurement from RBS effect, thus providing only the promoter strength.

UNIQd267ebbbf967645c-partinfo-00000005-QINU