Difference between revisions of "Part:BBa K115002:Experience"

Revision as of 18:34, 28 October 2010

This experience page is provided so that any user may enter their experience using this part.
Please enter how you used this part and how it worked out.

Applications of BBa_K115002

The parts were tested in luciferase constructs, by measuring luciferase activity after growing at certain temperatures. The fold increase of luciferase activity between cultures of cells grown at 20ºC and 37ºC is displayed in figure 1.

In this figure, 12 (the leftmost) is construct K115012, the reference strain, which has no thermosensitive RNA, but just B0032 as ribosome binding site. This is to compare for normal temperature induced behaviour in cells. The other constructs from 29-36 are K115029 to K115036, please look at the experience tab of these constructs to see which thermometer RNA they contain.

For more documentation, visit our wiki [http://2008.igem.org/Team:TUDelft (link)].

2010IGEM-TEAM NCTU_formosa's application

We using this parts as a regulator in our project's low-temperature release system. Part:BBa_K332031 Part:BBa_K332032 Part:BBa_K332033

We constructed series circuits' test as following article.

First, we made A+B circuit in the PSB3K3 plasmid. in this way we can use it to test by Using Flow Cytometry to obtain the data of A+B (for40°C, 37°C, 30°C, and 25°C)

and the following figures is our testing results. To test the efficiency of the temperature induced RBS and the interaction between tetR gene and ptet promoter, we replaced the crystal protein gene with GFP (green fluorescence protein) gene. In this scenario, GFP will simulate the crystal protein’s production, as it is easily detected by flow cytometry.

To conclude, we have verified that our strategy works. It demonstrates the regulation of GFP in a temperature dependent fashion, as it is evident the mean GFP values are significantly lower at T>37° C.

We expect our circuit design to allow steady bacteria growth and inhibit crystal protein at T>37° C, and high protein production and low bacteria growth rate at T<37° C

To make short of the matter,

at 25°C and 30°C (below 37° C): this RBS (BBa K115002) do not worked.
at 37°C and 40°C (above 37° C): this RBS (BBa K115002) do worked.

and we using those circits to make a modeling. The first equation describes the temperature control in strand A (Fig. 1).

Alpha-Temp is the production rates corresponding to transcriptional rate of constitutive promoter and the translation rate of the RBS BBa_K115002 which is a temperature sensitive post-transcriptional regulator.

The second equation describes the concentration of GFP change with time. Alpha-B is production rates of the GFP, which are assumed to be given constants.

To describe transition during log phase and stationary phase, the alpha-Temp and alpha-B and is assumed to zero when the Terminator in stationary phase. Gamma-TetR, and gamma-GFP are decay rates of the corresponding proteins.

When bacteria divide, the molecular in a bacterium will be dilute. Because bacteria grow faster, the dilution rate d(t) is included in this model and can be calculated from OD ratio of medium (Fig. 2). For an inhibition of TetR protein, Hill function is an S-shaped curve which can be described in the form 1 / (1 +x^n) (Alon, 2007). The values of the kinetic parameters used in the simulation were initially obtained from the literature and experimental data. Data computations were performed with Matlab software. A program was written and used as a subroutine in Matlab for parameter optimization using nonlinear regression (Fig. 3)

Fig. 2: The OD ratio is increased faster in log phase than it in stationary phase. The dilution rate d(t) can be calculated from OD ratio and used in out model.

User Reviews

UNIQa9c7c7f51ebaebb7-partinfo-00000000-QINU UNIQa9c7c7f51ebaebb7-partinfo-00000001-QINU