Difference between revisions of "Part:BBa K349112"

Line 4: Line 4:
 
A component of the Vio Operon which is used to produce a light green pigment from L-tyrosine.  Depending on which parts of the operon are available, a different colour will be produced.  Please note this piece is "naked",  meaning it does not contain a promoter, an RBS, or start and stop codons.  The promoter and terminator is intended to be reconstituted through the adjoining BA BioBytes attached through the BioBytes 2.0 assembly method.  
 
A component of the Vio Operon which is used to produce a light green pigment from L-tyrosine.  Depending on which parts of the operon are available, a different colour will be produced.  Please note this piece is "naked",  meaning it does not contain a promoter, an RBS, or start and stop codons.  The promoter and terminator is intended to be reconstituted through the adjoining BA BioBytes attached through the BioBytes 2.0 assembly method.  
  
<!-- Add more about the biology of this part here
 
 
===Usage and Biology===
 
===Usage and Biology===
 +
 +
This part is compatible with the Team Alberta 2010 Biobytes 2.0 assembly method. It can be utilized as an AB BioByte following digestion with BsaI and purification. The following protocol outlines the Biobytes 2.0 assembly method: <br>
 +
1) Mix the iron micro beads for 10 minutes.<br>
 +
2) Transfer 20 ul of iron micro beads to a 1.5 mL tube. <br>
 +
3) Pull the beads to the side using a magnetic tube rack. <br>
 +
4) Remove and discard the supernatant. <br>
 +
5) Add 50 ul of BioBytes 2.0 Wash Buffer to the beads. Flick gently to resuspend. <br>
 +
6) Pull the beads to the side using a magnetic tube rack. <br>
 +
7) Remove and discard the supernatant. <br>
 +
8) Repeat steps 5 to 7. <br>
 +
9) Add 200 ng of a premade anchor-Byte construct (premade in the GENOMIKON kit)  to the beads and top off the volume to 20ul with TE Buffer. Flick gently to resuspend. <br>
 +
10) Allow annealing for 30 minutes, mixing by flicking every 5 minutes. Ensure that there are no droplets on the sides of the tube. <br>
 +
11) Repeat steps 6 and 7. <br>
 +
12) Repeat steps 5 to 7. <br>
 +
13) Add 200 ng of the next BioByte of your construct, making sure that a BA Byte follows an AB Byte and vice versa. Add an appropriate amount of 2x QuickLigase Buffer, Quick Ligase and TE to a total volume of 20ul. <br>
 +
14) Flick gently to resuspend.  Allow ligation for five minutes, flicking gently every minute. <br>
 +
15) Add 30ul of Wash Buffer to the tube. Flick gently. <br>
 +
16) Repeats steps 6 and 7. <br>
 +
17) Repeat steps 5 to 7 twice. <br>
 +
18) Repeat steps 13 to 17 for each subsequent Byte addition, including the last BioByte. <br>
 +
19) After the last Byte has been ligated and washed, add 30 ul of 75C Elution Buffer. Keep at 75C for 10 minutes. <br>
 +
20) After 10  minutes, still at 75C, put the tube into a magnetic rack . Allow the beads to be pulled aside and collect the supernatant into a clean 1.5 mL tube. The supernatant will contain your construct. <br>
  
 
<!-- -->
 
<!-- -->

Revision as of 01:08, 28 October 2010

vioE-AB (BioBytes 2.0)

A component of the Vio Operon which is used to produce a light green pigment from L-tyrosine. Depending on which parts of the operon are available, a different colour will be produced. Please note this piece is "naked", meaning it does not contain a promoter, an RBS, or start and stop codons. The promoter and terminator is intended to be reconstituted through the adjoining BA BioBytes attached through the BioBytes 2.0 assembly method.

Usage and Biology

This part is compatible with the Team Alberta 2010 Biobytes 2.0 assembly method. It can be utilized as an AB BioByte following digestion with BsaI and purification. The following protocol outlines the Biobytes 2.0 assembly method:
1) Mix the iron micro beads for 10 minutes.
2) Transfer 20 ul of iron micro beads to a 1.5 mL tube.
3) Pull the beads to the side using a magnetic tube rack.
4) Remove and discard the supernatant.
5) Add 50 ul of BioBytes 2.0 Wash Buffer to the beads. Flick gently to resuspend.
6) Pull the beads to the side using a magnetic tube rack.
7) Remove and discard the supernatant.
8) Repeat steps 5 to 7.
9) Add 200 ng of a premade anchor-Byte construct (premade in the GENOMIKON kit) to the beads and top off the volume to 20ul with TE Buffer. Flick gently to resuspend.
10) Allow annealing for 30 minutes, mixing by flicking every 5 minutes. Ensure that there are no droplets on the sides of the tube.
11) Repeat steps 6 and 7.
12) Repeat steps 5 to 7.
13) Add 200 ng of the next BioByte of your construct, making sure that a BA Byte follows an AB Byte and vice versa. Add an appropriate amount of 2x QuickLigase Buffer, Quick Ligase and TE to a total volume of 20ul.
14) Flick gently to resuspend. Allow ligation for five minutes, flicking gently every minute.
15) Add 30ul of Wash Buffer to the tube. Flick gently.
16) Repeats steps 6 and 7.
17) Repeat steps 5 to 7 twice.
18) Repeat steps 13 to 17 for each subsequent Byte addition, including the last BioByte.
19) After the last Byte has been ligated and washed, add 30 ul of 75C Elution Buffer. Keep at 75C for 10 minutes.
20) After 10 minutes, still at 75C, put the tube into a magnetic rack . Allow the beads to be pulled aside and collect the supernatant into a clean 1.5 mL tube. The supernatant will contain your construct.

Sequence and Features


Assembly Compatibility:
  • 10
    COMPATIBLE WITH RFC[10]
  • 12
    COMPATIBLE WITH RFC[12]
  • 21
    COMPATIBLE WITH RFC[21]
  • 23
    COMPATIBLE WITH RFC[23]
  • 25
    COMPATIBLE WITH RFC[25]
  • 1000
    INCOMPATIBLE WITH RFC[1000]
    Illegal BsaI site found at 1
    Illegal BsaI.rc site found at 582