Difference between revisions of "Part:BBa K3037005"

Revision as of 18:22, 21 October 2019

MBP+eGFP+dCas9

Overview

This BioBrick was designed as a composite BioBrick by the team TU Dresden 2019. It is a fusion of dCas9 (BBa_K3037002) and eGFP (BBa_K3037006)(more information).

The dCas9 can bind to any sequence of DNA and eGFP (enhanced reporter protein) giving emission at the wavelength of 530 nm [1].

Additionally, the BioBrick is designed to have a N-terminal MBP fused to it (BBa_K3037001).This improves the solubility and expression, therefore, the total cytoplasmic yield of the protein. The MBP can further be used to purify the fusion protein on an amylose resin and, afterwards, can be cleaved off via digestion with PreScission protease.

This BioBrick was made based on BBa_K1994025. The BioBrick is a composed of a GFP and a dCas9. However, that case they are located in two different transcriptional units. In order to improve their design we decided to make it a fusion protein of the eGFP and dCas9.

Characterization

Outline

We performed the following characterization experiments:

1) Prove of DNA-binding ability of dCas9 via Electrophoretic Mobility Shift Assay (EMSA)

2) Expression in BBa_K3037000, purification and tag-removal

3) Expression using pOCC97 (BBa_K3037000) in E. coli pRARE T7

Experiments in Detail

1) Prove of DNA-binding ability of dCas9 via EMSA

1. Materials:

• 100 ng of PCR amplified sry gene
• 200 ng of dCas9-GFP
• 200 ng of guide RNA specifically targeting the amplified sry gene
• 1 x Reaction buffer - 20 mM Hepes buffer (pH 7.2)
  • 100 mM NaCl
  • 5 mM MgCl2
  • 0.1 mM EDTA

Six different guide RNAs were designed for targeting different regions of sry gene. Using the online tool Benchling and Fasta sequence of sry gene

1: AACTAAACATAAGAAAGTGA

2: GAAAGCCACACACTCAAGAA

3: ACTGGACAACAGGTTGTACA

4: GTAGGACAATCGGGTAACAT

5: TTCGCTGCAGAGTACCGAAG

6: CCATGAACGCATTCATCGTG

Table of the different guide RNAs with the context of the sequence and the PAM sequence

2. Methods:

1. We wanted to check if the overall efficiency of mobility shift increases when combinations of guide RNAs are used.

2. Guide RNA, dCas9-GFP and sry gene were incubated in reaction buffer (respective amounts mentioned in the materials section) for 37 °C for 1 hour.

3. Post incubation, they were mixed with loading dye without SDS, 20 % glycerol in Orange G dye and loaded onto 4-20 % gradient acrylamide- TBE precast gel. Gel was run for 3 hours at 75V in 1 x TBE buffer.

4. Gel was then stained using EtBR with 1:20000 dilution in 1x TBE for 10 minutes.

3.1 Results and Discussion of the 2 hours gel:

Electrophoretic Mobility Shift Assay (EMSA) of two hours of the Cas9 with different guide_RNAs

Lane 1 - There is a clear sry gene at 800 base pairs and when sry gene is incubated with only dCas9

Lane 2 - There is no shift seen in the position of the gene.

Lane 3 - When guide RNA 1 was incubated with the dCas9 DNA reaction mix, we saw a shift in the mobility, this is because of the protein DNA interaction and this binding is hindering the gene mobility.

Lanes 5,6,7,8 and 9 – Different combinations of guide RNAs were used. From lane 7 and 8 we see the highest mobility shift.

From the electromobility shift assay performed above, we conclude that our expressed dCas9-GFP protein is functional and is able to successfully bind to gene with the help of appropriate guide RNAs.

3.2 Results and Discussion of the 3 hours gel:

Electrophoretic Mobility Shift Assay (EMSA) of three hours of the Cas9 with different guide_RNAs

This second gel was run longer in order to get rid of all the secondary structures of the RNA formed.

From lane 3 to 7, no difference in the mobility of sry gene can be seen when only guide RNA is added to the reaction mix.

In Lane 8, 9 and 10 a mobility shift of the gene can be appreciated and in lane 11, when only guide RNA was loaded no bands were observed.

In lane 12, dCas9 is in the stacking part of gel, owing to higher molecular weight.

4. Conclusions:

- We have a functional dCas9 expressed, which is able to bind successfully to sry gene with the help of guide RNA.

- dCas9 on its own is unable to bind to sry gene, suggesting that for binding guide RNA is required.

- Guide RNA on their own is unable to cause mobility shift of sry gene.

2) Expression in BBa_K3037000, purification and tag-removal

The protein was purified via Amylose resin column with the a N-terminal-MBP-tag BBa_K3037001.

The truncated versions than can be seen in the gel were taken away by ion exchange chromatography, so in the last lane we only have the complete transcript

1.) Purification step, proving that MBP-tag is working: lane 4 (MBP FT) and lane 5 (MBP elution)

2.) Removal of the MBP-tag by digestion with 3C protease, proving that preScission site is intact and recognized

3.) Purification by cation Exchange chromatography on HiTrap SP column, purifiying away the cleaved off tag

Amilose resin purification using MBP-tag. The upper arrow shows the location in the gel of this BioBrick (BBa_K3037005). The lower ones show the MBP-tag after beeing cleaved off

3) Expression using pOCC97 (BBa_K3037000) in E. coli pRARE T7

With this experiment we proved that is easy to express diferent and functional BioBricks with this vector

Expression of different BioBricks in pOCC97

Sequence

NOTE: For some reason the specified scar when aploaded the sequence was the one of the RFC25 standard but the registry shows the one of the RFC23

References

[1] https://www.biotek.com/resources/technical-notes/excitation-and-emission-of-green-fluorescent-proteins/

[2] https://www.genscript.com/bacterial-soluble-protein-expression-MBP-tag.html

[3] https://www.gelifesciences.com/en/us/shop/chromatography/resins/affinity-tagged-protein/prescission-protease-for-gst-tag-removal-p-00248