Difference between revisions of "Part:BBa K2066119"

Revision as of 22:21, 19 October 2016

Synthetic Enhancer Project: 2X TetO Binding Cassette(52S) + NRII + sfGFP on UNS

This part takes the synthetic genetic circuit from Amit et. al. 2011 as well as the NRII promoter and coding region from Amit et. al. 2011 and puts it onto a BioBrick backone flanked by the UNS regions. Used for the synthetic enhancer project, this part consists of an enhancer region, that when bound to phosphorylated NRI protein, can bind to the promoter after the DNA loops to allow for these kinetics. The promoter and coding sequence for the NRII protein (which is mutated to be solely a kinase that can phosphorylate and activate the NRI and allow it to bind to the enhancer region) was taken from the Amit et. al. pACT Tet helper plasmid and put the sequence between the UNS 3 sequence. NRII was moved to the same plasmid as the synthetic enhancer to 1. reduce the circuit's dependence on LacI (which is also expressed in the original pACT Tet helper plasmid) as well as decrease the interference of these plasmids with the current bacterial circuitry and thus reduce the metabolic strain on the bacteria.

Once the looping and interaction between the enhancer and promoter happens, transcription of the NRI protein for positive feedback as well as the output flourescent reporter is initiated. This part is from the synthetic enhancer genetic circuits created by Amit et. al where there is a tetR binding cassette with two TetO binding sites in the spacer region between the enhancer and the promoter. The two binding sites allows for three discrete states of output: a repressed, intermediate, and unrepressed state. Small chemical induction with aTc binds to and inactivates available TetR repressor. When a small amount of aTc is present, there isn't enough aTc to find TetR proteins and there is enough repressor available to allow for a constant filling of the two available TetO binding sites. When both TetO sites are bound, the DNA becomes less flexible and makings looping of the enhancer to the promoter extremely difficult, thus not allowing for very minimal transcription of the NRI and reporter proteins. When more aTc is added to the system, more TetR is bound and inactivated and this creates an intermediate step where enough TetR is bound that at any point only one TetR is bound to the teto sites and this increases the rigidity of the DNA and allows for looping and activation and reporter output less frequently. Finally, when aTc conentration is high, you reach a saturation point where almost all TEtR repressors are bound and inactivated and you get maximal amount of looping and thus maximal amount of NRI and reporter transcribed and translated.

This part should be transformed with Bba_I739001 to get consititutive expression of TetR repressor.

Source:

The enhancer, tet cassette, glnAp2 synthetic promoter, and NRI coding region sequences were derived from the synthetic enhancer circuits from Amit, R., Garcia, H. G., Phillips, R. & Fraser, S. E. Building enhancers from the ground up: a synthetic biology approach. Cell146, 105–118 (2011). The NRII2302 coding region and the promoter that it is controlled by is derived from the helper plasmid pACT tet from Amit et. al 2011. The sfGFP flourescent reporter design is inspired by C. Lou, B. Stanton, Y.-J. Chen, B. Munsky, C. A. Voigt, Ribozyme-based insulator parts buffer synthetic circuits from genetic context. Nat. Biotechnol. 30, 1137 (2012). doi:10.1038/nbt.2401 pmid:23034349. The UNS sequences at the ends of the insert are derived from Torella, J. P., Boehm, C. R., Lienert, F., Chen, J. H., Way, J. C., & Silver, P. A. (2013). Rapid construction of insulated genetic circuits via synthetic sequence-guided isothermal assembly. Nucleic acids research, gkt860. A huge thanks to all the researchers involved in its original creation!

Sequence and Features