Difference between revisions of "Assembly:RBS-CDS issues"

Revision as of 14:23, 23 June 2006

Note: page needs reformatting

Transfer Curves

The [http://openwetware.org/wiki/Endy:F2620/Transfer_Curve transfer curve] of a BioBrick device is measured from input PoPs to output PoPs. (More on PoPs [http://parts2.mit.edu/wiki/index.php/Abstraction_hierarchy_and_PoPS here].) For a protein-DNA inhibition system, the transfer curve depends on the rates and efficiencies of many stages in a chain that includes:

• transcriptional efficiency
• mRNA lifetime
• ribosome binding efficiency
• translation initiation and efficiency
• protein lifetime
• protein concentration
• protein multimerization
• protein-DNA binding rates and efficiencies
• cooperative effects with other molecules
• RNA polymerase effects
• system copy count

and more system-specific variables, few if any of which can be measured directly.

If BioBrick parts are to be interoperable, intentional engineering of this chain of events will be required to produce a desired transfer function.

Ribosome Binding Sites (RBS)

Different RBS bind ribosomes with different efficiencies. While the overall efficiency may not be directly proportional to this efficiency, it is an important variable. In the future, we expect that this data book will have a table such as the following:

Standard BioBrick Ribosome Binding Sites

A BioBrick engineer armed with this table could perform a first-order reengineering of the transfer function by measuring a component with BBa_B0031 and then selecting a more appropriate RBS.

In order to allow easy variation in the RBS, some BioBrick parts have their RBS and their protein coding regions implemented in separate parts. The combined, normalized part is also available for convenience. In order to divide the BioBrick part into its RBS and coding region, a set of BioBrick restriction sites must be designed.

Standard Assembly and the RBS

The RBS is physically near the start codon. (In BioBricks, this will always be ATG.) The "sequence logo", similar to a consensus sequence, for the RBS is shown below. The size of each letter is proportional to the frequency of that base in the RBS.

The RBS sequence logo, from Tom Schneider, [http://www-lmmb.ncifcrf.gov/%7Etoms/sequencelogo.html "A Gallery of Sequence Logos"]</small>

This figure shows the RBS as an A/G-rich region about 10 bases upstream of the start codon. This leaves little room for a BioBrick restriction enzyme site. The standard assembly method of BioBricks normally results in an 8-base region containing a 6-base mixed SpeI/XbaI restriction site surrounded by a base on each end as shown below. If a start codon followed this sequence, the RBS would be significantly disturbed.

      --T ACTAGA G--

This problem is solved by changing the rightmost base from a G to a T. This results in the sequence shown below and limits the impact of the BioBrick overhead to six bases.

Summary

When variable RBS sequences are developed as BioBrick parts, they should have the standard BioBrick prefix and suffix as follows:

    GAATTC GCGGCCGC T TCTAGA G[RBS]
     EcoRI  NotI      XbaI

    [RBS]T ACTAGT A GCGGCCG CTGCAG
           SpeI     NotI    PstI

When a protein coding region is designed to be preceded by a BioBrick RBS part, it should have the following prefix and suffix sequences:

    GAATTC GCGGCCGC T TCTAG[ATG Remaining CDS]
     EcoRI  NotI      XbaI

    [CDS]T ACTAGT A GCGGCCG CTGCAG
           SpeI     NotI    PstI

Notes

• The only change is that the protein coding region prefix does NOT end with AGAG. instead, it ends AGATG with the ATG also being the start codon of the protein coding region.

• In BioBrick parts, we prefer using TAA as the stop codon.