Difference between revisions of "Part:BBa K568003"

(Usage and Biology)
Line 7: Line 7:
 
===Usage and Biology===
 
===Usage and Biology===
 
This part can be used as a reporter plasmid. It expresses beta-galactosidase if there is a T7 polymerase (or a mutant variant) nearby or transcribed through another part.  
 
This part can be used as a reporter plasmid. It expresses beta-galactosidase if there is a T7 polymerase (or a mutant variant) nearby or transcribed through another part.  
The polymerase binds to the T7 promoter and transcription of the lacZ-Gene can occur, leading to beta-galactosidase expression.
+
The polymerase binds to the T7 promoter and transcription of the lacZ-gene can occur, leading to beta-galactosidase expression.
 
+
  
 
===Experimental Testing===
 
===Experimental Testing===

Revision as of 15:13, 21 September 2011

T7 promoter lacZ reporter part

beta-galactosidase expression upon T7 polymerase binding


Usage and Biology

This part can be used as a reporter plasmid. It expresses beta-galactosidase if there is a T7 polymerase (or a mutant variant) nearby or transcribed through another part. The polymerase binds to the T7 promoter and transcription of the lacZ-gene can occur, leading to beta-galactosidase expression.

Experimental Testing

The part was tested by the 2011 team of the TU_Munich on the 25th of September 2011. For this purpose, a Miller Assay was conducted using E. coli BL21 (DE3). This strain expresses T7 polymerase upon induction with IPTG.

The experiment was conducted as follows: Overnight cultures of BL21(DE3) transformed with BBa_K568003 and DH5 alpha transformed with Part:BBa_I732017 (as negative control) were set to an OD_600 of about 0.7 and incubated for another 30 min.

A first data-set was recorded. The OD_600 of all cultures was measured as follows:

10 µl of each culture was mixed with 500 µl Z-Buffer, 40 µl chloroform, 20 µl 0.1 % SDS and 430 µl LB medium. After vortexing for 10 sec, the samples were centrifuged for 1 min at 13000 rpm. 20 µl ONPG (4 mg/ml) were added to 100 µl sample. Immediately after this, the reaction was stopped by adding 50 µl Na2CO3 (1 M). The start- and end-time of the reaction was measured. The OD_420 and OD_550 were measured and the Miller Units were calculated using the following formula:

TU Munich 2011 Equation Miller Assay.jpg

Then, the culture of BL21 (DE3) containing BBa_K568003 was devided into equal portions which were then induced with 0.01 mM, 0.1 mM, 1.0 mM, 1.5 mM or no IPTG. The negative control was incubated with 1.0 mM or no IPTG. After every 30 min, a new data-set was taken.


It was expected that IPTG-induced E. coli BL21 (DE3) transformed with BBA_K568003 should yield higher Miller Units than uninduced ones. The results can be seen below.


Results of the Miller Assay of BBa_K568003. The part was transcribed by genome-coded T7 polymerase, which was induced by addition of varying concentrations of IPTG. The control strain was not able to produce T7 polymerase.
















The data shows that the cultures induced by isopropyl-β-D-1-thiogalactopyranoside (IPTG) yield higher Miller Units than the uninduced control after 60 min. Therefore, a higher amount of β-galactosidase was produced. This shows that the part works as expected. Furthermore a slight quantitative dependence of the Miller Units on the concentration of IPTG can be seen. After 120 min the Miller Units of the culture induced with 1.0 mM IPTG go down again, which might be evidence for increasing of proteolysis caused by death of bacteria. The reason for this might be a too high concentration of IPTG which results in extreme over expression of protein which might "exhaust" the cells and thus kill them. It can also be observed that the uninduced control yields higher Miller Units than the β-galactosidase negative, induced control. This can be explained by leaky biosynthesis of the genome-coded T7 polymerase. If the production of T7 polymerase is more tightly controlled, the level of expressed β-galactosidase should go down to the minimum of the negative, induced control.



Sequence and Features


Assembly Compatibility:
  • 10
    COMPATIBLE WITH RFC[10]
  • 12
    COMPATIBLE WITH RFC[12]
  • 21
    COMPATIBLE WITH RFC[21]
  • 23
    COMPATIBLE WITH RFC[23]
  • 25
    COMPATIBLE WITH RFC[25]
  • 1000
    COMPATIBLE WITH RFC[1000]