Difference between revisions of "Part:BBa K1957003:Design"

m (→‎Design Notes)
m (→‎Design Notes)
 
(One intermediate revision by the same user not shown)
Line 7: Line 7:
  
 
===Design Notes===
 
===Design Notes===
−
This is one of of the three FeFe Hydrogenase subunits. To make the entire FeFe Hydrogenase construct the following BioBricks need to be ligated with BBa_K1957003: BBa_K1957004 and BBa_K1957001. pSB1C3 would not conjugate properly into S.oneidensis, thus the three subunits were ligated using golden gate cloning into the pBAD expression vector.
+
This is one of of the three FeFe Hydrogenase subunits. To make the entire FeFe Hydrogenase construct the following BioBricks need to be ligated with BBa_K1957003: BBa_K1957004 and BBa_K1957001.  
  
−
BBa_J04450, which contained pSB1C3, would not conjugate properly into S.oneidensis, most likely due to conflicts in the origin of replication. The conflict could result in low copy numbers of pSB1C3 in S.oneidensis resulting in little antibiotic resistance. pSB1C3 contains pUC19 derived pMB1 origin of replication. In a paper by Myers and Myers (1997) they observed that pMB1 did not replicate in Shewanella oneidensis MR-1, formerly known as Shewanella putrefaciens MR-1.
+
BBa_J04450, which contained pSB1C3, would not conjugate properly into S.oneidensis, possibly due to conflicts in the origin of replication. The conflict could result in low copy numbers of pSB1C3 in S.oneidensis resulting in little antibiotic resistance. pSB1C3 contains pUC19 derived pMB1 origin of replication. In a paper by Myers and Myers (1997) they observed that pMB1 did not replicate in Shewanella oneidensis MR-1, formerly known as Shewanella putrefaciens MR-1.
  
 
To overcome this issue, the three subunits were ligated into the pBAD expression vector using Golden Gate cloning
 
To overcome this issue, the three subunits were ligated into the pBAD expression vector using Golden Gate cloning
Line 19: Line 19:
  
 
===References===
 
===References===
 +
Myers C.R. and Myers J.M. (1997). 'Replication of plasmids with the p15A origin in Shewanella putrefaciens MR-1', Applied Microbiology, 24, pp.221-225

Latest revision as of 20:45, 8 October 2016


HydB (N-terminally tagged) subunit of FeFe Hydrogenase


Assembly Compatibility:
  • 10
    COMPATIBLE WITH RFC[10]
  • 12
    COMPATIBLE WITH RFC[12]
  • 21
    COMPATIBLE WITH RFC[21]
  • 23
    COMPATIBLE WITH RFC[23]
  • 25
    COMPATIBLE WITH RFC[25]
  • 1000
    INCOMPATIBLE WITH RFC[1000]
    Illegal BsaI site found at 1
    Illegal BsaI.rc site found at 369


Design Notes

This is one of of the three FeFe Hydrogenase subunits. To make the entire FeFe Hydrogenase construct the following BioBricks need to be ligated with BBa_K1957003: BBa_K1957004 and BBa_K1957001.

BBa_J04450, which contained pSB1C3, would not conjugate properly into S.oneidensis, possibly due to conflicts in the origin of replication. The conflict could result in low copy numbers of pSB1C3 in S.oneidensis resulting in little antibiotic resistance. pSB1C3 contains pUC19 derived pMB1 origin of replication. In a paper by Myers and Myers (1997) they observed that pMB1 did not replicate in Shewanella oneidensis MR-1, formerly known as Shewanella putrefaciens MR-1.

To overcome this issue, the three subunits were ligated into the pBAD expression vector using Golden Gate cloning

Source

The source of the part will be its sequence which was retrieved from GenBank.


References

Myers C.R. and Myers J.M. (1997). 'Replication of plasmids with the p15A origin in Shewanella putrefaciens MR-1', Applied Microbiology, 24, pp.221-225