Difference between revisions of "Part:BBa K3037000"

Biology

The lactose operon (lac operon) is a polycistronic bacterial operon that encodes the genes of lactose metabolism. It is consists of three structural genes: a promoter, an operator and a terminator. A bacterial cell synthesizes enzymes involved in lactose metabolism only under two conditions: in the presence of lactose and when the cells is lacking glucose. [1]

The regulation of the lac operon occurs according to the principle of negative feedback: the more lactose is present in the environment - the more enzymes for its catabolism is synthesized (positive direct connection); the more enzymes are present in a cell - the less lactose remains, and finally, the less lactose in the environment - the less enzymes are produced (double negative feedback).[2]

In the absence of lactose in the cell, or at a low concentration, the repressor protein reversibly binds to the operator region and inhibits transcription. The reporter protein is a product of the LacI monocistronic operon. In the absence of lactose in the cell, enzymes for lactose metabolism are not synthesized. Besides, if the glucose concentration in the cell is sufficient to maintain metabolism, activation of the lactose operon also does not occur. The promoter sequence of the lactose operon is weak, therefore, even in the absence of a repressor protein in the operator site, transcription is practically not initiated.

When the concentration of glucose in the cell decreases, the enzyme adenylate cyclase is activated. Glucose is an inhibitor of this enzyme and activates phosphodiesterase, which catalyzes the conversion of the cAMP molecule to AMP. Adenylate cyclase catalyzes the conversion of ATP to the cyclic form - cAMP. cAMP binds to a catabolism activating protein (CAP), and a complex is formed that interacts with the promoter of the lactose operon. It changes its conformation, and increases the affinity of RNA polymerase for this site. In the presence of lactose, expression of the operon genes occurs.[2]

Klaus I. Matthaei, in Handbook of Stem Cells, 2004

Experiments in Detail

1) Expression of different proteins (BBa_3037003)(BBa_K3037007) with growth curve

Two different proteins were expressed using this backbone: HRP (BBa_K3037007) and a bigger fusion protein (BBa_K3037003). The constructs were expressed in E. coli pRARE T7.

The results prove that when expressed, none of our two proteins inhibits the growth of the bacteria, yet the growing ratio is lower in the culture that is expressing a bigger protein.

Comparison of growth of differently sized proteins.

Expression of composite BioBrick MBP-HRP BBa_K3037008.

2) Expression of proteins with the plasmid before and after optimization at different temperatures

To use this backbone as convenient expression vector in iGEM, we had to include the Prefix and Suffix of the BioBrick Assembly. Subsequentially, we compared the expression of the original vector we recieved, pOCC97, to our optimized version for iGEM, BBa_K3730000.

We found that the original plasmid had a XbaI site, which we used to insert our BioBrick BBa_K3037003. This ilegal restriction site was later removed with an overhang PCR. The original XbaI restriction site was positioned downstream of the T7 polymerase promoter and upstream the RBS sequence of the plasmid. This way only BioBricks that already has a RBS fused to them could be expressed. Since we were using the RFC25 standard of Freiburg for our fusion proteins, the inserted protein contained already its own RBS in the Prefix.

However, we experienced on our own how difficult it is to add such a small sequence, as an RBS, to our other constructs. Therefore we redesigned the plasmid to be ready for expression in a single digestion+ligation reaction. We removed the XbaI restriction site and included a Prefix and Suffix of the RFC 10 standard after the RBS of the plasmid.

We used the BioBrick assembly method to insert our BioBrick BBa_K3037003, which has its own RBS due to the RFC 25 standard.

The following graphs shows the expression of the protein BBa_K3037003 using both plasmids (optimized and not optimized) and also different IPTG concentrations for induction and temperature.

Comparison of the growth curves of optimized and not optimized pOCC97.

The comparison of the growth curves shows that, although, the new plasmid adapted to the RFC 10 standard didn't affect the growing rate of the bacteria, as the original one.

Comparison of the growth curve compared before and after optimization

3) SDS-PAGEs for the expression assay over the time of Full Construct (BBa_K3037003)

Comparison of the expression of MBP-HRP (BBa_K3037008) and Full Construct (BBa_3037003)

SDS-PAGE results for comparison of expression of different proteins in the vector before and after optimization

Expression of full construct in pOCC97 not optimized at 18ºC

SDS-PAGE results for comparison of expression of fusion protein BBa_K3037003 at 37ºC before optimization

Expression of Full Construct in pOCC97 at 37ºC

SDS-PAGE results for comparison of expression of fusion protein BBa_K3037003 at 37ºC before optimization

SDS-PAGE results for comparison of expression of fusion protein BBa_K3037003 at 37ºC before optimization

Expression of Full Construct in pOCC97 optimized

SDS-PAGE results for comparison of expression of fusion protein BBa_K3037003 after optimization

4) Image analysis of the expression in the SDS-PAGEs with ImageJ

The previously shown SDS-pages were then further analysed by using the software ImageJ to correct for loading differences and be able to draw conclusions about the best conditions to express the Full Construct in POCC97.

Temperature and IPTG induction dependence of the optimized POCC97

Expression of the Full Construct in optimized pOCC97 under different conditions.

Temperature and IPTG induction dependence of the not optimized POCC97

Expression of the Full Construct in not optimized pOCC97 under different conditions.

Comparison between optimized and not optimized POCC97

Comparison between the expression of optimized and not optimized POCC97.

Conclusion

Based on this analysis, it can be concluded that optimal conditions for the expression of our fusion protein, BBa_3037003, are overnight expression at 18ºC while inducing with 0.5 mM IPTG. We are proud to say that our optimized pOCC97 shows a increased expression robustness under varying conditions over time.

5) Expression of different BioBricks in pOCC97

With this experiment we proved that is easy to express different BioBricks functionally with this vector.

Expression of different BioBricks in pOCC97

Sequence

Design Notes

This BioBrick was designed to fit the RFC 10 standard using the primers:

Forward: tactagtagcggccgctgcagCCGTTATAGAAGCTTGAGTATT

Reverse: gaattcgcggccgcttctagagGCCCATGGATATATCTCCTTCT

References

1. Jacob F; Monod J. Genetic regulatory mechanisms in the synthesis of proteins, J Mol Biol. journal, 1961, vol. 3: p. 318—356.

2. J. Parker, Encyclopedia of Genetics, 2001