Difference between revisions of "Part:BBa K3254018"

(Orthogonality Characterization)
 
Line 3: Line 3:
 
<partinfo>BBa_K3254018 short</partinfo>
 
<partinfo>BBa_K3254018 short</partinfo>
  
This is a conservative design of phiC31 integrase coding sequence. This sequence was isolated from a streptomyces shuttle vector and the EcoRI site was removed. Comparing to [[Part:BBa_K1039012|BBa_K1039012]], this design has a longer coding region, and the "atg" start codon was replaced by "gtg" codon. Because there is an start codon in the upstream, some researchers likely annotated it as a part of the coding sequence. Here we design this part and placed it after a RiboJ([[Part:BBa_K1679038|BBa_K1679038]]) sequence for achieving a appropriate response interval of phiC31 integrase.
+
This was a conservative design of phiC31 integrase coding sequence. This sequence was isolated from a streptomyces shuttle vector and the EcoRI site was removed. Comparing to [[Part:BBa_K1039012|BBa_K1039012]], this design had a longer coding region, and the "atg" start codon was replaced by "gtg" codon. Because there was an start codon in the upstream, some researchers likely annotated it as a part of the coding sequence. Here we designed this part and placed it after a RiboJ([[Part:BBa_K1679038|BBa_K1679038]]) sequence for achieving a appropriate response interval of phiC31 integrase.
  
 
=Thermodynamic Characterization=
 
=Thermodynamic Characterization=

Latest revision as of 11:48, 21 October 2019


original sequence of phiC31 integrase gene

This was a conservative design of phiC31 integrase coding sequence. This sequence was isolated from a streptomyces shuttle vector and the EcoRI site was removed. Comparing to BBa_K1039012, this design had a longer coding region, and the "atg" start codon was replaced by "gtg" codon. Because there was an start codon in the upstream, some researchers likely annotated it as a part of the coding sequence. Here we designed this part and placed it after a RiboJ(BBa_K1679038) sequence for achieving a appropriate response interval of phiC31 integrase.

Thermodynamic Characterization

  • A new translational unit BBa_K3254010 including this part was constructed.
  • The cis-element used in this experiments were BBa_K3254000 which contains the phiC31 att sites.
  • We constructed an IPTG inducible system to control the expressional level by the IPTG concentration in E.coli DH5α host.
  • The distribution ratios of the cells with original att sites or recombined att sites were measured using a flow cytometry.

Genetic Design

  • The composition and principle of the experimental system were indicated below. More details can be seen on the pages of BBa_K3254010 and BBa_K3254000.
  • BBa_K3254025 can be seen as a reference of device structure.
The composition and principle of the experimental system

Experimental Setup

The two plasmids were co-transformed into E.coli DH5α host. Then we selected colonies with no observable fluoresce and inoculated into M9 supplemented medium for overnight growth. Then, the cell cultures were diluted 1000-fold with M9 supplemented medium with gradient concentrations of IPTG inducer and growth for another 20 hours. All incubations were carried out using a Digital Thermostatic Shaker maintained at 37 °C and 1000 rpm, using flat-bottom 96-well plates sealed with sealing film. Finally, 3-μL samples each culture were transferred to a new 96-well plate containing 200 μL per well of PBS supplemented with 2 mg/mL kanamycin. The fluorescence distribution of each sample was assayed using a flow cytometry.

  • M9 medium (supplemented): 6.8 g/L Na2HPO4, 3 g/L KH2PO4, 0.5 g/L NaCl, 1 g/L NH4Cl, 0.34 g/L thiamine, 0.2% casamino acids, 0.4% glucose, 2 mM MgSO4, and 100 μM CaCl2.

Results

  • The recombination rate could be controlled by IPTG concentration and had a very narrow hypersensitivity response interval (the blue circle indicate the phiC31 testing group).
  • Because the Ptac promoter had a nearly-linear response curve (see BBa_K3254025), it was more likely that the hypersensitivity was due to the characteristics of the integrase itself rather than the characteristics of the transcriptional regulation system.

T--GENAS China--RR-IPTG.png

Orthogonality Characterization

We conducted orthogonality tests to see the compatibility between the 6 integrase used in our project. The other integrases included Int5, Int7, Int8, Int10 and TG1.

Genetic Design

Similar to the design of thermodynamic characterization. Each integrase generator plasmid was co-transferred with 6 plasmid containing different sets of cis-elements.

Experimental Setup

The growth condition was similar to the thermodynamic characterization but every sample was full induced with 500 μM IPTG. Then we used specific primers to identify the genotype of att sites by PCR. The principle of genotype identification was shown on the right of result image.

Results

The results indicated that phiC31 integrase had a good orthogonality with the other 5 att sites and compatible with other integrases. IBR-C35/F55/S37/E21/T25/G22 were the plasmids with phiC31/Int5/Int7/Int8/Int10/TG1 att sites.

T--GENAS China--orthogonality test.png

Sequence and Features


Assembly Compatibility:
  • 10
    COMPATIBLE WITH RFC[10]
  • 12
    COMPATIBLE WITH RFC[12]
  • 21
    INCOMPATIBLE WITH RFC[21]
    Illegal XhoI site found at 75
  • 23
    COMPATIBLE WITH RFC[23]
  • 25
    COMPATIBLE WITH RFC[25]
  • 1000
    INCOMPATIBLE WITH RFC[1000]
    Illegal SapI site found at 1689
    Illegal SapI.rc site found at 1380
    Illegal SapI.rc site found at 1438
    Illegal SapI.rc site found at 1543