Difference between revisions of "Part:BBa K2918050"

Revision as of 09:21, 21 October 2019

Cross-species based iFFL

Genetic implementation of an incoherent feed forward loop (iFFL) in which a stabilized broad host range (P_BHR) promoter is controlling GFP expression.

Sequence and Features

The two transcriptional units in this composite part are oriented outwards.

Usage and Biology

A incoherent feed-forward loop (iFFL) is a unique control systems motif where the output signal is robust to changes in the input signal. This is achieved by the introduction of a repressor.

iFFL can be applied to genetic circuits to achieve expression independent from copy number, transcriptional and translational rates. To implement the iFFL in a genetic circuit, TALE proteins can be used. These proteins consist of repeats where 12th and 13th amino acids can vary, these are called the repeat variable diresidue (RVD). RVDs have been shown to bind to DNA in a simple one-to-one binding code (Doyle, Stoddard et al., 2013). The direct correspondence between amino acids allows scientists to engineer these repeat regions to target any sequence they want. In our system, we used the TALE protein as a repressor by engineering promoters to contain the binding site of this specific TALE protein (0.1 T7sp1 promoter, 0.5 T7sp1 promoter and P_BHRsp1 promoter).
In our genetic circuit, a unrepressed promoter controls the expression of TALE protein while the promoters with the TALE binding sites drive expression of GFP.

When transcriptional units are placed in series, due to low effieciency of terminators, leaky expression of the gene in the neighbouring transcriptonal unit can occur. This significantly influences the behavior of the iFFL genetic circuit (Segall-Shapiro et al., 2018). Hence, the transcriptional units in the circuit are oriented outward to achieve insulation from influence of the neighboring transcriptional unit.

An interesting application of the iFFL is to achieve controllable gene expression across different bacterial species. Gene expression in different bacterial contexts is influenced by changes in copy number, transcriptional and translational rates. iFFL based on broad host range promoters (P_BHR promoter and P_BHRsp1 promoter) has been demonstrated below to achieve controllable expression between E. coli and P. putida .

Strain Construction

The construct was assembled by golden gate assembly based modular cloning system. First, the individual transcriptional units were cloned into level 1 destination vectors pICH47761 and pICH47822 by BpiI based golden gate assembly. The multi-transcriptional unit construct was assembled by a BsaI based golden gate. The assembly was a one-pot restriction-ligation reaction where the individual level 1 constructs were added along with the destination vector pICH48055. The correct clone was distinguished by blue-white screening and the construct was confirmed by sequencing. The cloning protocol can be found in the MoClo section below.

Modular Cloning

Modular Cloning (MoClo) is a system which allows for efficient one pot assembly of multiple DNA fragments. The MoClo system consists of Type IIS restriction enzymes that cleave DNA 4 to 8 base pairs away from the recognition sites. Cleavage outside of the recognition site allows for customization of the overhangs generated. The MoClo system is hierarchical. First, basic parts (promoters, UTRs, CDS and terminators) are assembled in level 0 plasmids in the kit. In a single reaction, the individual parts can be assembled into vectors containing transcriptional units (level 1). Furthermore, MoClo allows for directional assembly of multiple transcriptional units. Successful assembly of constructs using MoClo can be confirmed by visual readouts (blue/white or red/white screening). For the protocol, you can find it here.

Note: The basic parts sequences of the Sci-Phi 29 collection in the registry contain only the part sequence and therefore contain no overhangs or restriction sites. For synthesizing MoClo compatible parts, refer to table 2. The complete sequence of our parts including backbone can be found here.

Table 1: Overview of different level in MoClo

For synthesizing basic parts, the part of interest should be flanked by a BpiI site and its specific type overhang. These parts can then be cloned into the respective level 0 MoClo parts. For level 1, where individual transcriptional units are cloned, the overhangs come from the backbone you choose. The restriction sites for level 1 are BsaI. However, any type IIS restriction enzyme could be used.

Table 2: Type specific overhangs and backbones for MoClo. Green indicates the restriction enzyme recognition site. Blue indicates the specific overhangs for the basic parts

Characterization

We first characterized the functioning of this system through modeling. According to our model this system always yields the same gene of interest (GOI) expression levels when the copy number of the plasmid, transcriptional and translational rates of both genes (TALE and GOI) are changed in the same ratio. When transferring a genetic circuit between organisms all of these variables change. In order to demonstrate this systems ability to have stable expression across species we cloned this BioBrick into E. coli and P. putida

Using the PBHR and PBHRsp1, we constructed an iFFL genetic circuit driving GFP expression. The circuit was transformed in E. coli and P. putida and, output fluorescence was measured by flow cytometry during the logarithmic growth phase. To correct for background fluorescence, E. coli and P. putida without plasmids were used as blanks. GFP under the control of PBHRsp1 was used as a positive (unrepressed) control. As the cell morphologies of E. coli and P. putida are different they cannot be compared directly, gating was based on the most dense regions in the scatter plot for each organism. In order to compare the GFP expression levels between each organism, the background fluorescence for each organism was subtracted by its respective blank .

The protocol for preparation of samples for the flow cytometry assay is as follows:

1. Samples were grown overnight
2. Overnight cultures were diluted to OD = 0.01 into 1 mL, and grow for 2 hours on 30 degrees 250 rpm shaking in 2 mL Eppendorf tubes.
3. Overnight cultures were diluted 1:100 into 5 mL, and grow for 4 hours on 30 degrees 250 rpm shaking in 50 mL eppendorf tubes.

Figure 3 shows that our Pbhr based iFFL results in only a 2351 difference in fluorescence, while in the unrepressed system the expression is 578530.

References

• Lou, C., Stanton, B., Chen, Y.-J., Munsky, B., & Voigt, C. A. (2012). Ribozyme-based insulator parts buffer synthetic circuits from genetic context. Nature Biotechnology, 30(11), 1137–1142.