Difference between revisions of "Part:BBa K2918014"
Line 188: Line 188:
 
<br>
 
<br>
  
 +
From figure 3, strength of universal RBS is shown to be 60% higher than BBa_B0032. 
  
  

Revision as of 22:33, 19 October 2019

Universal RBS

Ribosome Binding Site which is functional in both gram positive and gram negative bacteria.

Sequence and Features


Assembly Compatibility:
  • 10
    COMPATIBLE WITH RFC[10]
  • 12
    COMPATIBLE WITH RFC[12]
  • 21
    COMPATIBLE WITH RFC[21]
  • 23
    COMPATIBLE WITH RFC[23]
  • 25
    COMPATIBLE WITH RFC[25]
  • 1000
    COMPATIBLE WITH RFC[1000]

The part has been confirmed by sequencing and has no mutations.

Overview

This ribosomal binding site has been made by the use of the RBS calculator 2.0 by (Yang et al., 2017). The RBS functions both in gram negative (E. coli) and gram positive (B. subtilis). It has been demonstrated to work in P. putida .

Strain Construction

The DNA sequence of the part was synthesized by IDT with flanking BpiI sites and respective Modular Cloning (MoClo) compatible 5'UTR overhangs. For this particular RBS, the downstream overhang 'AATG' can be modified to 'ATG' since the RBS sequence ends with adenine. This design choice will allow for seamless cloning between the 5'UTR and coding sequence leaving no part-junction sequences. The RBS was then cloned in a level 0 MoClo backbone pICH41246 and the sequence was confirmed by sequencing. The cloning protocol can be found in the modular cloning section below.

Modular Cloning

Modular Cloning (MoClo) is a system which allows for efficient one pot assembly of multiple DNA fragments (Weber et al., 2011). The MoClo system consists of Type IIS restriction enzymes that cleave DNA 4 to 8 base pairs away from the recognition sites. Cleavage outside of the recognition site allows for customization of the overhangs generated. The MoClo system is hierarchical. First, basic parts (promoters, UTRs, CDS and terminators) are assembled in level 0 plasmids in the kit. In a single reaction, the individual parts can be assembled into vectors containing transcriptional units (level 1). Furthermore, MoClo allows for directional assembly of multiple transcriptional units. Successful assembly of constructs using MoClo can be confirmed by visual readouts (blue/white or red/white screening). For the protocol, you can find it here.


Note: The basic parts sequences of the Sci-Phi 29 collection in the registry contain only the part sequence and therefore contain no overhangs or restriction sites. For synthesizing MoClo compatible parts, refer to table 2. The complete sequence of our parts including backbone can be found here.


Table 1: Overview of different level in MoClo

Level Basic/Composite Type Enzyme
Level 0 Basic Promoters, 5’ UTR, CDS and terminators BpiI
Level 1 Composite Transcriptional units BsaI
Level 2/M/P Composite Multiple transcriptional units BpiI

For synthesizing basic parts, the part of interest should be flanked by a BpiI site and its specific type overhang. These parts can then be cloned into the respective level 0 MoClo parts. For level 1, where individual transcriptional units are cloned, the overhangs come from the backbone you choose. The restriction sites for level 1 are BsaI. However, any type IIS restriction enzyme could be used.


Table 2: Type specific overhangs and backbones for MoClo. Green indicates the restriction enzyme recognition site. Blue indicates the specific overhangs for the basic parts

Basic Part Sequence 5' End Sequence 3' End Level 0 backbone
Promoter NNNN GAAGAC NN GGAG TACT NN GTCTTC NNNN pICH41233
5’ UTR NNNN GAAGAC NN TACT AATG NN GTCTTC NNNN pICH41246
CDS NNNN GAAGAC NN AATG GCTT NN GTCTTC NNNN pICH41308
Terminator NNNN GAAGAC NN GCTT CGCT NN GTCTTC NNNN pICH41276


Characterization

The Universal RBS was characterized by comparing it to BBa_B0032 . For comparision of the two RBSs, they were cloned in the same backbone (pICH47761) and were paired with the same promoter (T7sp1). The strengths were compared by measuring flourescence readout from harmonized GFP by flow cytometry and E.coli BL21 DE(3) cells were used as blank. Click here for the protocol. FCSalyzer v.0.9.18-alpha was used to analyze data from the flow cytometry experiment.
The scatter plot in figure 1 was used to gate the most dense cell regions of the blank and the same gating was considered to obtain the flourescence values depicted in figure 1. Cells of similar forward and side scatter were compared.

Modeling


Figure 1: Scatter plot of forward and side scatter of E. coli BL21 DE(3) cells.

Gating was performed on the data in the flourescnece histogram (figure 2) to discern between flourescent and non-flourescent cells.

Modeling


Figure 2: Raw fluorescence data. The curves represent flourscenece values of E.coli BL21 DE (3) cells (black), clones with BBa_B0032 (red) and clones with Universal RBS (blue).

From figure 2 the median fluorescence intensity of the two samples was obatined and corrected by the flourescence of E.coli BL21 DE(3) cells. Figure 3 depicts the flourescence of GFP expression influenced by BBa_B0032 and Universal RBS.

Modeling


Figure 3: Fluorescence values of for BBa_B0032 and Universal RBS with median fluorescence of E. coli BL21 cells without a plasmid substracted.

From figure 3, strength of universal RBS is shown to be 60% higher than BBa_B0032.


References