Difference between revisions of "Part:BBa K2607000:Experience"

Revision as of 18:13, 14 October 2018

This experience page is provided so that any user may enter their experience using this part.
Please enter how you used this part and how it worked out.

[iGEM 2018 UI_Indonesia] Finding Diphthy: Experiment with HB-EGF/Tar (HT) Receptor (BBa_K2607001)

We performed experiment to study the interaction between DiphTox (DT) (BBa_K2607000) and HB-EGF/Tar (HT) receptor (BBa_K2607001) using binding assay and luminescence (Promega's ADP-Glo^TM Kinase) assay. Figure 1 shows complete workflow of this experiment.

Figure 1. Original plan workflow to study interaction between DT (BBa_K2607000) and HT (BBa_K2607001).

DT and HT Cloning
Upon receiving DT and HT (in gBlocks) from Integrated DNA Technologies, Inc. (IDT), we performed PCR to amplify the gBlocks. PCR amplification for all gBlocks used the designated forward (Fwd) and reverse (Rev) cloning primers. Furthermore, cycling formula for PCR cloning and confirmation could be accessed in the iGEM 2018 UI_Indonesia team's lab notes [http://2018.igem.org/Team:UI_Indonesia/Notebook], as we applied GoTaqTM Long PCR enzyme as the Hi-Fi polymerase. The amplified gBlocks were then used as inserts to plasmid vectors. For HT BioBrick, IDT was unable to yield the full sequence in high purity, so we had to split HT into two fragments (HT-1 and HT-2), which would later be amplified, restricted with SalI, and ligated to obtain complete HT fragment.

On the other hand, we also prepared vectors for carrying our parts. Backbone pSB1C3-mRFP (BBa_J04450) has been used widely in our process of traditional cloning, for it provides much sensitive selection upon transformed recombinant plasmids. Since this plasmid does not contain any available expression promoter for the designed BioBrick, our supervisor suggested the usage of pQE80L expression vector belonged to Institute of Human Virology and Cancer Biology (IHVCB) lab for functional assays and analyses. Therefore, we used pSB1C3 as cloning vector for submission to iGEM Headquarters and pQE80L as cloning vector for expression.

We conducted traditional cloning (restriction-ligation) method to introduce our previously amplified inserts into prepared vectors. Restriction digestion was done sequentially with EcoRI and PstI in total of 8 hours by using the same buffer (i.e. EcoRI buffer and bovine serum antigen (BSA) 1X) with a minimum DNA template of 10 µg. Desalting and low-melting agarose (LMA) 1% electrophoresis purification was done to further remove any possible contaminating enzymes and undesired polynucleotides. Ligation of both vectors and inserts were conducted by adding T4 ligase and its respective buffers to be later incubated 160C overnight.

Transformation of resultant recombinant plasmids was done in wild-type Escherichia coli K-12 (for submission purpose) and BL21(DE3) (for characterization and validation purpose). To enhance selection of recombinant E. coli, the transformed products were spread into selective LB agar containing appropriate antibiotic. Antibiotic formulation was complied to the lab’s proven antibiotics sensitivity test. We solubilized the powdered chloramphenicol in ethanol 95% and ampicillin in distilled water until final concentration of 25 mg/ml and 100 mg/ml, respectively. They were then added into LB media with ratio of 1:1000. After spread into LB agar, the transformed products were then incubated at 37⁰C overnight.

In the case of transformation with pSB1C3, to select the colony with desired inserts, we performed red-white screening. If the grown colonies were red, it indicated that the colonies were transformed by native pSB1C3-mRFP and we excluded the colonies. We only picked white colonies (indicated that mRFP had been successfully removed from pSB1C3 and possibly replaced by insert) to be further confirmed for desired insert presence by colony PCR. We used VF2 and VR primers (i.e. iGEM standard primers) for confirmation of inserts in pSB1C3, while we used our hand-made designed primers for confirmation of inserts in pQE80L.

Finally, we performed mini-prep plasmid isolation for any confirmed colonies with desired inserts in pSB1C3. We grew the colonies in LB liquid medium at 37⁰C shaken overnight. Sequencing was performed to confirm the sequence of inserts before submitted to iGEM Headquarters.

Figure 2. Colonies of E. coli BL21(DE3) with pQE80L-DT in LB agar containing ampicillin.

Figure 3. Ultraviolet (UV) illumination of E. coli transformed with pSB1C3-DT. Red-white screening could be utilized since our team used pSB1C3-mRFP as initial backbone vector.

Figure 4. Gel analysis of colony PCR on pQE80L-DT transformed into E. coli BL21(DE3). PCR colony primer would amplify ~250 bp bands that located inside the DT BioBrick, indicating that the DT fragment was successfully cloned into pQE80L.

Figure 5. Gel analysis of PCR colonies on pSB1C3-DT transformed E. coli TOP10. Universal flanked primers of VF2 and VR in pSB1C3 would amplify ~600 bp bands that were found in several following colonies, indicating that the DT fragment was successfully cloned into pSB1C3.

Figure 2 and 3 shows the process on how we selected the colonies with possible recombinant plasmids, while Figure 4 and 5 shows the final results of DT colony PCR confirmation. From these results, we concluded that DT BioBrick was successfully inserted into pSB1C3 and pQE80L backbone.

User Reviews

UNIQ2dd269cff03d81c2-partinfo-00000000-QINU UNIQ2dd269cff03d81c2-partinfo-00000001-QINU