Difference between revisions of "Part:BBa K559010:Experience"

Revision as of 21:09, 5 October 2011

This experience page is provided so that any user may enter their experience using this part.
Please enter how you used this part and how it worked out.

Characterizations of BBa_K55901

First, we need to characterize its gene size and sequence.

We use PCR with six pairs of primers and gel electrophoresis to confirm that we have properly constructed halorhodopsin complete system (BBa_K559010) (Fig. 1). All bands in each lane match their theoretical sizes. Halorhodopsin complete system then was transformed to BL21(DE). Since our halorhodopsin has been HIS-tagged, we performed western blot to confirm the expression of halorhodopsin in BL21(DE) (Fig. 2). The PCR and western blot results indicate that our biobricks is successfully constructed and halorhodopsin can be properly expressed in BL21(DE).

Figure 1. Halorhodopsin complete system (BBa_K559010) was correctly constructed. Components in the plasmid were amplified by standard PCR using corresponding primers. The PCR conditions were 95°C denature for 30s, 54 °C annealing for 15s and 72°C extension for 30s. The number of PCR cycle was 30. The PCR products of corresponding lanes are shown on the table. T7 was amplified by T7 F and T7 R, HR was amplified by HR F and HR R, 24C was amplified by 24C F and 24C R, T7 HR was amplified by T7 F and HR R, T7 24C was amplified by T7 F and 24C R and HR 24C was amplified by HR F and 24C R.

This biobrick made has to be optimized for maximize protein expression.

Figure 2. Optimization of Halorhodopsin expression in BL21(DE). BL21(DE) was transformed according to standard protocol. Bacterial culture grew from a single colony at 37℃ in the presence of chloramphenicol. Different concentration of IPTG was used to induce gene expression of Halorhodopsin when OD600 reached 0.4. After IPTG induction for 4 hours, bacterial samples were collected and disrupted. Bacterial samples were analyzed by 12% SDS-PAGE. Halorhodopsin was HIS-tagged and was detected by anti-His antibody with dilution 1:5,000. Secondary antibody was anti-mouse antibody with dilution of 1:2,000 was used. Bacterial proteins in lysate stained by coomassive brilliant blue served as loading control.

Figure 3. Growth curve of bacteria under different NaCl concentration. BL21(DE) was transfomrmed according to standard protocol. Bacterial culture grew from a single colony at 37°C. 0.1 mM of IPTG was used to induce Halorhodopsin expression. 1% (v/v) inoculum was used as start culture at 0 hour. The change in OD600 was monitored.

Figure 4. Halorhodopsin expressing bacteria absorbed chloride ions. BL21(DE) was transformed and bacterial culture grew from a single colony at 37°C in the presence of light. 0.1 mM of IPTG and 0.4 M of NaCl were included in the culture medium. Intracellular Cl- was determined by MQAE after 4 hours induction.

Figure 5. Halorhodopsin expressing bacteria absorbed chloride ions under different condition. BL21(DE) was transformed and bacterial culture grew from a single colony at 37°C under different conditions. Bacterial samples were collected when OD600 reached 0.4. Bacteria from different growth conditions were disrupted. The intracellular Cl- was determined by MQAE. Light: bacteria grew in the presence of light. IPTG: 0.1 mM of IPTG was used to induce gene expression. NaCl: the LB contained 0.4 M of NaCl. “+” indicates the corresponding component was included. “-” indicates the corresponding component was missed.

Figure 6. Halorhodopsin expressing bacteria absorbed chloride ions induced by laser with different wavelengths. BL12(DE) was transformed by BBa_K559010 and the bacterial culture grew from a single colony in LB with 0.4 M of NaCl at 37°C in the absence of light. Bacterial samples were collected when OD600 reached 0.4. 500 μl of bacterial sample was excited by 20% laser power with different wavelength for 2 minutes under confocal microscope. 200 μl of excited bacteria was collected and disrupted. Its intracellular chloride ion concentration was measured by MQAE. Error bar represents SEM.

Figure 7. Bacterial growth after exposure to different power of laser with wavelength 530 nm. Transformed BL21(DE) grew in LB with 0.4 M of NaCl. 500 μl of bacteria culture was used for laser exposure when OD600 reach 0.4. Bacteria were exposed to different laser power for 2 minutes. After the exposure, 200 μl of the bacteria was cultured in 2 ml of LB. OD600 was determined immediately after inoculation (0 hour) and after 2 hour grew in LB. Table shows the value of OD600 at corresponding time point. Data was expressed as mean ± SEM.

Figure 8. Laser (530 nm) induced Chloride ion absorption. BL12(DE) was transformed and a single colony was picked to grow in LB with 0.4 M of NaCl. 500 μl of bacterial sample with OD600 reached 0.4 was excited by laser (530 nm) with different LASER power (%). 200 μl of excited bacteria was collected and disrupted. The intracellular concentration of chloride ion was determined by MQAE.

Figure 9. Chloride ions absorption responded differently with the length of laser (530 nm) exposure. BL12(DE) was transformed and a single colony was picked to grow in LB with 0.4 M of NaCl. 500 μl of bacterial sample with OD600 reached 0.4 was excited by LASER (530 nm) with different exposure time. The LASER power was fixed at 25%. 200 μl of excited bacteria was collected and disrupted. The intracellular concentration of chloride ion was determined by MQAE.

Applications of BBa_K559010

Application 1

We apply this biobrick system for the Computer-aided light-coupled gene expression regulation platform.

Figure 1: The Computer-aided light-coupled gene expression regulation platform is shown for

Figure 2. The agarose gel photo shows the Pgad cassette size information. Genes regulated by Pgad cassette are only expressed with presence of sodium chloride. Zymographic analysis of cell wall hydrolase activity in cell extracts prepared from samples taken 6 hours after addition of 0.5 M NaCl to cultures at an OD600 of 0.5. Lane 1: lacZ; Lane 2: lacZ+NaCl; Lane 3: lytPR; Lane 4: lytPR+NaCl; Lane 5: acmA; Lane 6: acmA+NaCl. [1]

Application 2

Figure 3. Voltage against sodium chloride concentration test shows the capability using entropy-mixing electrodes to monitor extracellular sodium chloride concentration. The electrodes were immersed in 25 ml sodium chloride solutions with different concentrations until the voltage achieved a steady level. The steady voltages were recorded and plotted.

References: [1]J.W. Sanders, G. Venema, and J. Kok, “A chloride-inducible gene expression cassette and its use in induced lysis of Lactococcus lactis,” Applied and environmental microbiology, vol. 63, Dec. 1997, p. 4877.

User Reviews

UNIQdb52077919b0e129-partinfo-00000000-QINU UNIQdb52077919b0e129-partinfo-00000001-QINU